764004

Vonroc ET502AC Manual

7
Zoom out
Zoom in
Previous page
1/40
Next page
EN
7
WWW.VONROC.COM
Vibration level
The vibration emission level stated in this instruc-
tion manual has been measured in accordance
with a standardized test given in EN60745; it may
be used to compare one tool with another and as
a preliminary assessment of exposure to vibration
when using the tool for the applications mentioned.
• Using the tool for different applications, or with
different or poorly maintained accessories, may
significantly increase the exposure level.
• The times when the tool is switched off or when
it is running but not actually doing the job, may
significantly reduce the exposure level.
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work patterns.
DESCRIPTION
The numbers in the text refer to the diagrams on
pages 2 - 3.
1. Reload lever
2. Cartridge shaft
3. Switch
4. Lock on button
5. Top
6. lock off button
7. Cartridge filling level window
8. Safety pin
3. OPERATION
Application (Fig. B)
For this tool, use one of the following length for
staples or nails:
• Staples: 6 up to 14 mm
• Nails: 15 mm
Loading the nails or staples (Fig. 3)
• Choose the correct nail or staple for the job.
• Hold the tacker with bottom upwards.
• Open de cartridge shaft (2) by slightly pressing
the reload lever (1)
• Pull the reload lever backwards to open the
cartridge shaft(2).
For nails:
•
Place the nails upside down against the left side
of the cartridge shaft (2). The left side also shows
a nail-symbol on the cartridge shaft, see fig.4
For staples:
• Place the staples upside down in the cartridge
shaft (2).
• Push the reload lever to fully close the cartridge
shaft.
Before loading the tacker, make sure the
machine is in lock on position and it is
disconnected from the mains supply.
Never load staples and nail at the same time.
Checking the cartridge shaft
The cartridge filling level window (7) indicates the
amount of staples/nails inside the cartridge shaft.
Using the tacker
After every load test the machine on a piece
of scrape.
• Press the Lock Off switch (6) to unlock the
machine.
NOTE: The machine does not work when Lock on
switch (4) is pressed. Even though connected to
the mains supply.
•
Press the lock On switch (4) to lock the machine.
NOTE: When not in use, press the lock On switch
to lock the machine and disconnect from the
mains supply.
NOTE: Always store in Lock on (4) position.
Placing the tool
1. Place the tool on workpiece at the spot where
the staple or nail should be located.
2. Press the tool down firmly by pressing the ma-
chine on the top (5) with one hand.
3. Use your other hand to operate the switch (3).
4. By pressing the machine down firmly you lift the
safety of the machine.
Warning! The safety of the machine will be
lifted when pressure is applied to the safety
pin (8) on the bottom of the machine.
Always make sure the tacker mouth is in
direct contact with the material when
pressing the switch.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc ET502AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc ET502AC in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info