764004

Vonroc ET502AC Manual

6
Zoom out
Zoom in
Previous page
1/40
Next page
6
EN
WWW.VONROC.COM
the fastener causing an injury.
• Do not actuate the tool unless the tool is placed
firmly against the workpiece. If the tool is not in
contact with the workpiece, the fastener may
be deflected away from your target.
• Disconnect the tool from the power source
when the fastener jams in the tool. While
removing a jammed fastener, the tacker may be
accidentally activated if it is plugged in.
• Use caution while removing a jammed fastener.
The mechanism may be under compression and
the fastener may be forcefully discharged while
attempting to free a jammed condition.
• Do not use this tacker for fastening electrical
cables. It is not designed for electric cable
installation and may damage the insulation of
electric cables thereby causing electric shock
or fire hazards.
Before using the tacker
• Check the following points:
• Do the voltage of the engine and the engine
safe-guard, if any, correspond to the mains
voltage (appliances for a mains voltage of
220-240 V);
• Are the mains lead and the mains plug in
a good condition: solid, without any loose
ends or damage.
•
Always wear eye protection when using the tool.
• Maintain the tool with care.
•
Check for misalignment or binding of moving
parts, breakage of parts, and any other con-
dition that may affect the tools operation. If
damaged, have the tool serviced before using.
• Check if the slide cartridge has been fastened
properly.
• Do not use the tool in a humid environment.
• Do not use the tool on materials containing
asbestos.
• Secure the workpiece firmly. Use clamps or a
vice to firmly hold the workpiece. This results in
a safer grip than with your hand.
• Always ensure that the cable is behind the
device.
Using the tool
• Do not use the tool if the switch does not move
in “Lock” or “Unlock” position.
•
Always hold the tool with two hands while starting.
• Always keep the cord away from the moving
parts of the machine.
• Keep your hands away from the work piece.
• In the case of jamming by a nail or staple,
switch the machine immediately in lock position
and remove the plug from the mains.
• Never aim the tool at people or animals.
• Use only staples or nails fit for this tool.
• Make sure not to damage any leads when using
the tool.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the voltage of the power
supply corresponds to the voltage on the
rating plate label.
Class II machine - Double insulation - You
don’t need any earthed plug.
Remove all staples/nails from the magazine
after each use
2. MACHINE INFORMATION
Intended use
The tacker enables you to fasten various materi-
als, such as fabric, wood, gauze, cardboard and
leather. Therefore, the tool is suitable to upholster
furniture, to wrap objects or to repair shoes.
TECHNICAL SPECIFICATIONS
Model No. ET502AC
Voltage 220-240V~
Frequency 50 Hz
Number of staples/nails 30/min.
Staples 6 up to 14 mm
Nails 15 mm
Weight ca. 0.65 kg
Sound pressure level L
PA
73.8+3 dB(A)
Acoustic power level L
WA
84.8+3 dB(A)
Vibration
4.678+1.5 m/s
2
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc ET502AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc ET502AC in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info