Manual Vonroc CS502AC (page 9 of 80) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish)

778299

Zoom out

Zoom in

1/80

WWW.VONROC.COM

For replacing the saw blade, it is best to set the

depth to 0mm and set the bevel angle to 0°.

Afterwards, the machine can be placed on its side,

resting on the motor housing and baseplate.

Removing the saw blade

1. Press and hold the spindle lock (19) button.

2. Loosen the clamping bolt (15) using the hex key

provided, turning in anti-clockwise direction.

3. Remove the clamping bolt (15) and clamping

ﬂange (16).

4. Retract the lower guard (14) by using the lever

(12) and remove the saw blade.

Mounting the saw blade

1. Clean the saw blade and all clamping parts to

be assembled.

2. Retract the lower guard (14) by using the lever

(12) and mount the saw blade. Ensure the

arrow on the saw blade corresponds with the

arrow on the lower guard (14).

3. Mount the clamping ﬂange (16). Ensure the

ﬂat sides of the clamping ﬂange correspond

with the ﬂat sides of the blade shaft. Also make

sure the convex side of the clamping ﬂange is

mounted to the outside.

4. Press and hold the spindle lock (19) button.

5. Mount the clamping bolt (15) using the hex key

provided, turning in clockwise direction.

Attaching the parallel guide (Fig. D)

1. Loosen the clamping bolt for parallel guide (10)

2. Mount the parallel guide (22) onto the basepla-

te (17).

3. Set the desired cutting width using the scale

on the parallel guide (22) and the cutting mark

on the baseplate (17). The 45° cutting mark (8)

indicates the position of the saw blade for 45°

angled cuts. The 0° cutting mark (9) indicates the

position of the saw blade for right-angled cuts.

4. Tighten the clamping bolt (10).

4. OPERATION

Switching the machine on/off (Fig. A, B)

• To start the machine, press and hold the lock-

off button (3) and press the on/off switch (2).

• To stop the machine, release the on/off switch

(2).

Adjusting the bevel angle (Fig. A, B)

The 0° cutting mark (9) indicates the position of the

saw blade for straight cuts. The 45° cutting mark

(8) indicates the position of the saw blade for 45°

cuts.

1. Loosen the clamping bolt (7)

2. Adjust the baseplate (17) to the desired posi-

tion (0°- 45°). The sawing angle (bevel) can be

read on the scale (6).

3. Tighten the clamping bolt (7).

Adjusting the cutting depth (Fig. C)

1. Loosen cut depth clamping lever (20).

Move the baseplate (17) to the desired position.

The sawing depth) can be read on the scale (21).

3. Tighten cut depth clamping lever (20).

Optimum use

• Hold the work using clamps or a vice to have

both hands free to operate the saw.

• Switch on the saw and place the bottom plate

on the work.

•

Slowly move the saw towards the previously dra-

wn cutting line and slowly press the tool forward.

• Firmly press the bottom plate on the work,

otherwise the circular saw may start to vibrate,

causing the blade to break more easily.

• Let the saw do the job. Do not put undue pres-

sure on the circular saw.

5. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

mains plug from the mains.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that the

ventilation openings are free of dust and dirt. Re-

move very persistent dirt using a soft cloth moiste-

ned with soapsuds. Do not use any solvents such

as gasoline, alcohol, ammonia, etc. Chemicals such

as these will damage the synthetic components.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc CS502AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 6.06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vonroc CS502AC Manual

Product: