819186
7
Zoom out
Zoom in
Previous page
1/112
Next page
EN
7
WWW.VONROC.COM
TECHNICAL SPECIFICATIONS
Model No. CR506AC /
CR506AC_GREY /
CR506AC_WHITE
Compressor type Piston - oil free -
lownoise
Compressor drive Direct drive
Voltage 220-240V~
Frequency 50 Hz
Input power 750W
Horsepower 1 HP
Operating mode S3 50% *
Idling speed 1450/min
IP class IP30
Protection class Class I
Air intake 128 l/min
Output (compressed air) at 7 bar 42 l/min
Output (compressed air) at 4 bar 65 l/min
Max. outlet pressure 8 bar
Cut-in pressure approx. 6 bar
Cut-out pressure approx. 8 bar
Tank capacity 24L
Cable length 2m
Weight 23 kg
Sound pressure level L
pA
= 79.7 dB(A)
K
pA
= 3 dB(A)
Sound power level L
WA
= 92.7 dB(A)
K
WA
= 3 dB(A)
* S3 = intermittent operation without the impact of
the start-up. This means that during a period of 10
minutes, the maximum operating time is 50% (e.g.
5 minutes of work and 5 minutes of rest) , under
optimal environmental conditions (max. temp
25°C). Respecting these guidelines and the prescri-
bed maintenance intervals will allow the product to
work properly over time.
DESCRIPTION
The numbers in the text refer to the diagrams on
page 2-3.
1. Cover
2. Switch
3. Pressure switch
4. Pressure regulator
5. Quick coupler (outlet)
6. Pressure gauge (operating pressure)
7. Pressure gauge (tank pressure)
8. Safety valve
9. Handle
10. Pressure pipe
11. Drain cock
12. Air inlet
13. Air filter
14. Overload switch
15. Tank
16. Rubber feet
17. Bolts
18. Washers
19. Nuts (for feet)
20. Wheels
21. Axle bolts
22. Lock washers
23. Nuts (for wheels)
24. Allen screws
3. ASSEMBLY
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Mounting the wheels (Fig. A, B)
1. Insert the wheel axle bolt (21) into the intended
hole of the wheel (20).
2. Mount the wheel (20) on one side of the tank
(15). Using the supplied lock washer (22) and
nut (23) as shown on figure B.
3. Tighten the nut (23) by using a wrench.
4. Repeat these steps for the other wheel (20) on
the other side of the tank (15).
Assembling the rubber feet (Fig. A, C)
1. Insert the bolt (17) into the intended hole of the
washer (18).
2. Insert the bolt (17) into the intended hole of the
rubber foot (16).
3. Mount the rubber foot (16) on one of the two
mounting points on the bottom of the tank (15)
as shown on figure C.
4. Tighten the nut (19) by using a wrench.
5. Repeat these steps for the other foot (16) on
the other mounting point.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc CR506AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc CR506AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 12.22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info