819207
7
Zoom out
Zoom in
Previous page
1/84
Next page
EN
7
WWW.VONROC.COM
The charger has 2 LED indicators (12) which indi-
cate the status of the charging process:
Red LED Status Green LED status Charger status
Off Off No power
Off On
Standby mode:
- No battery is
inserted or,
- Battery inserted
but charging has
nished
On Off Battery charging in
progress
Inserting the Cartridge
Pull the rack (3) backwards using the rack handle
(7).
Cut open the front side of the cartridge and screw
on a dispensing nozzle.
Insert the cartridge into the cartridge holder (1).
Slide the unlocked rack (3) forwards until the
plunger (2) comes into contact with the cartridge.
If necessary, cut the dispensing nozzle to size, so
that it ideally meets your requirements.
4. OPERATION
Adjusting the Feed Rate
You may adjust the feed rate of the rack (3) by
pressing the (+) or (-) buttons (5/6) while simul-
taneously pressing the trigger switch (8).
Four different speeds can be selected, the
selected speed is shown by the indicator lights
(4). Note that the amount of material squeezed
out depends on two factors: The size of the
opening in the dispensing nozzle and the se-
lected feed rate.
Switching On and Off
To switch on the caulking gun, press the trigger
switch (8). The rack (3) will start moving for-
wards.
To switch off the caulking gun, release the
trigger switch (8). The rack (3) will move back-
wards slightly into a parking position to stop
unwanted dripping.
Working Advice
Comply with the manufacturer's instructions
regarding the material to be applied. Certain
materials can only be used within a certain
temperature range or can only be applied to
specifi c surfaces.
Open and use the cartridges in accordance with
the manufacturer's specifi cations.
Only trim the dispensing nozzle if the material is
securely within the cartridge holder.
Adjust the feed rate to ensure a smooth and
consistent application of material in one appli-
cation.
Ensure that the surface onto which the material
is to be applied is clean, dry and free from
grease.
5. MAINTENANCE
Maintenance and Cleaning
Remove the battery from the power tool
before carrying out work on the power tool
(e.g. maintenance, changing tool, etc.). The
battery should also be re-moved for
transport and storage. There is risk of injury
from unintentionally pressing the on/off
switch.
To ensure safe and effi cient operation, always
keep the power tool and the ventilation slots
clean.
Clean the dispensing nozzles, the cartridge
holder and the rack with he press thoroughly
after each use in accordance with the speci-
cations provided by the manufacturer of the
consumable. The battery and the handle can be
cleaned using a damp cloth.
The caulking gun is maintenance-free and does
not contain any parts that need to be replaced
or maintained.
ENVIRONMENT
Faulty and/or discarded electrical or
electronic apparatus have to be collected at
the appropriate recycling locations.
Only for EC countries
Do not dispose of power tools into domestic waste.
According to the European Guideline 2012/19/EC
for Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that
are no longer usable must be collected separately
and disposed of in an environmentally friendly way.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc CG501DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc CG501DC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 3.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info