763912

Vonroc CD506DC Manual

7
Zoom out
Zoom in
Previous page
1/48
Next page
EN
7
WWW.VONROC.COM
Warning! This power tool produces an
electromagnetic field during operation.
This field may under some circumstances
interfere with active or passive medical
implants. To reduce the risk of serious or
fatal injury, we recommend persons with
medical implants to consult their physician
and the medical implant manufacturer
before operating this power tool.
2. MACHINE INFORMATION
Intended use
This screw driver is intended for driving in and
loosening screws.
TECHNICAL SPECIFICATIONS
Model No CD506DC
Output of charger 5V DC Max. 1000mA
Rechargeable Battery pack 4V Li-ion 320 mAh
Battery charging time 70-90 minutes
Chuck capacity 1/8" (4mm) hex
No load speed 120 /min
Sound pressure level L
PA
39.5 dB(A) K=3 dB(A)
Sound power level L
WA
50.5 dB(A) K=3 dB(A)
Hand-arm vibration a
h
(screw driving without impact) 0.149 m/s
2
K=1.5 m/s
2
Vibration level
The vibration emission level stated in this instructi-
on manual has been measured in accordance with
a standardized test given in EN62841; it may be
used to compare one tool with another and as a
preliminary assessment of exposure to vibration
when using the tool for the applications mentioned.
• Using the tool for different applications, or with
different or poorly maintained accessories, may
significantly increase the exposure level.
• The times when the tool is switched off or when
it is running but not actually doing the job, may
significantly reduce the exposure level.
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work patterns.
DESCRIPTION
The numbers in the text refer to the diagrams on
pages 2-3.
1. Machine
2. Battery indication light
3. Work light button
4A . Counterclockwise switch
4B. Clockwise switch
5. Base cover
6. Work light
7. Bit holder
8. Screwdriver bit
9. Base
10. Charging socket
3. OPERATING
The machine must be charged before first
use.
Charging the machine (Fig. B)
In order to charge the machine, insert the small
micro-USB plug of the charger cable into the char-
ging socket (10) on the side of the machine (1).
Subsequently plug the large USB plug connector
into a USB outlet. The battery indication light (2)
will show the charging progress.
Fully charging the battery may take up to 70-90
minutes.
Fitting and removing drills or screwdriver bits (Fig. C)
The machine bit holder (7) is suitable for drills
and screwdriver bits with a standard 1/8” (4mm)
hexagonal shaft. To fit a screwdriver bit:
• Insert the screw driver bit (8) into the machine’s
bit holder (7), it will be hold by a magnet.
• The screw driver bit can be removed by pulling
it out of the bit holder again.
Switching the machine on and off (Fig. A)
• Pressing the Counterclockwise switch (4A) will
activate the machine to loosen screws.
• Pressing the Clockwise switch (4B) will activate
the machine to tighten screws.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc CD506DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc CD506DC in the language / languages: English, German, Dutch, French, Polish, Spanish as an attachment in your email.

The manual is 3,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info