778559

Vonroc AG503AC Manual

10
Zoom out
Zoom in
Previous page
1/88
Next page
10
EN
WWW.VONROC.COM
6. Side handle connection point
7. Side handle
8. Allen key
9. Rear handle
10. Handle release knob
11. Spindle
12. Mounting flange
13. Wheel disc (not included)
14. Clamping nut
15. Spanner
3. ASSEMBLY
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Assembling the protection guard (Fig. C and D)
1. Place the machine on a table with the spindle
(11) facing upwards.
2. Place the protection guard (3) over the machine
head as shown in Figure C making sure the ridg-
es on the protection guard fall into the notches
of the machine head.
3. Turn the protection guard counter clockwise as
shown in Figure D.
4. Fix the the allen screw (2) on the guard (3) with
the allen key (8).
5. You can adjust the position of the protection
guard by releasing the allen screw (2), adjust the
guard to the desired position and fixing the allen
screw again.
Never attempt to remove the guard.
Mounting and removing the wheel disc (Fig. B)
Do not use the machine without the guard.
Only use sharp and undamaged wheel discs.
• Always use suitable wheel disc for this machine
with diameter Ø 230 mm and a bore from 22.2
mm the thickness of the wheel disc should be
6 mm for wheel disc for grinding and 3 mm for
wheel disc for cutting, the mounting wheel disc
may not touch the safety guard.
Mounting
1. Place the machine on a table with the protection
guard (3) facing upwards.
2. Mount the flange (12) onto the spindle (11).
3. Place the wheel disc (13) onto the spindle (11).
4. Keep the spindle lock button (1) pressed and
firmly tighten the clamping nut (14) onto the
spindle (11) by using the spanner (15).
Removing
1. Place the machine on a table with the protec-
tion guard (3) facing upwards.
2. Keep the spindle lock button (1) pressed and loos-
en the clamping nut (14) using the spanner (15).
3. Remove the wheel disc (13) from the spindle (11).
4. Keep the spindle lock button (1) pressed and
firmly tighten the clamping nut (14) using the
spanner (15).
Mounting the side handle (Fig. A and E)
• The side handle (7) can be screwed into one of
the three side handle connection points (6).
4. OPERATION
Make sure that the work piece is properly
supported or fixed.
Rear handle (Fig. A)
Before rotating the handle, always switch
off the machine and remove the mains plug
from the mains.
1. To unlock the handle (9), push and hold the
handle release knob (10).
2. Rotate the handle (9) into one of the 3 available
positions and release the handle release knob
(10).
Before switching the tool on, ensure the
handle release knob (10) clicks and locks
into place when changing handle position.
Switching on and off (Fig. A)
• To switch the machine on, push the switch for-
ward and press the on/off switch (5).
• To switch the machine off, release the On/off
switch (5).
• Hold the machine away from the work piece
when turning it on and off because the wheel
disc could damage the work piece.
• Clamp the work piece firmly or use another meth-
od to ensure that it cannot move while working.
• Check the discs regularly. Worn wheel discs have
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc AG503AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc AG503AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 8.89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info