769323

Visonic Powermaster-360 Manual

26
Zoom out
Zoom in
Previous page
1/96
Next page
26 D-307500 PowerMaster 360 Installer's Guide
4.4.6 Configuring soak test mode
This option enables you to enter device zones into Soak Test mode.
To Enable the Soak Test proceed as follows:
Step 1
Step 2
Step 3
Step 4
Step 5
Select ADD TO SOAK
TEST Option
[1]
Select the respective
device Group
[2]
Select device zone
number
[3]
Select to enable or
disable the Soak Test
[4]
[5]
02:ZONES/DEVICES
CONTACT SENSORS
Z09:Motion Sens
ID No. 120-2468
ADD TO SOAK TEST
MOTION SENSORS
Disable test
Enable test
See
[5]
to
Step 3
– Enabling Soak Test mode
[1]
Enter the Installer Mode menu, select the 02.ZONES/DEVICES option (see section 4.2) and then select the ADD
TO SOAK TEST option.
[2]
Select the respective Group of the device you require to add the Soak Test. For example, MOTION SENSORS.
[3]
Scroll to select the specific device zone number.
[4]
Select between Disable test (default) or Enable test.
[5]
If set to Enable Test you must set the duration of the Soak Test before the Soak Test will start (see section 4.5.8).
You can stop the test for the relevant zone by changing the setting to Disable test at any time during the testing
period. All Soak test zones will be reset to start a new test upon occurrence of one of the following: 1) Power up
of the system; 2) Setup of Factory Default; 3) Change in system Soak Time.
4.4.7 Defining configuration defaults for device settings
PowerMaster-360 enables you to define the default parameters used during enrollment and to change them whenever
you require so that new devices enrolled into the system will be configured automatically with these default parameters
without the need to modify the configuration of each new enrolled device. You can use a certain set of defaults for
certain group of devices and then change the defaults for another group.
IMPORTANT! Devices that were already enrolled in the PowerMaster-360 system before the defaults have been
changed will not be affected by the new default settings.
To define the default parameters of a device Group proceed as follows:
Step 1
Step 2
Step 3
Step 4
Step 5
Select DEFINE
DEFAULTS Option
[1]
Select the respective
device Group
[2]
Select the Default
Parameter
[3]
Select the new
Default Setting
[4]
[5]
02:ZONES/DEVICES
CONTACT SENSORS
DEFINE DEFAULTS
MOTION SENSORS
Alarm LED
Event Counter
Disarm Activity
Low
High
See
[5]
to
Step 3
– Changing Defaults
[1]
Enter the Installer Mode menu, select the 02.ZONES/DEVICES option (see section 4.2) and then select the
DEFINE DEFAULTS option.
[2]
Select the respective Group of the device you require to define the defaults for (for example, MOTION SENSORS).
[3]
Scroll the parameter list of the Device Group and select the Default Parameter you require to change, for example
Event Counter. The list combines the parameters of all devices in the group, for example, the parameters of all
types of Motion sensors.
[4]
In the example, the existing default setting of the Event Counter for enrolled motion sensors was
Low Sensitivity (marked with ) . To change it to High, scroll the menu until the display shows High and press
the button. The new default for the Event Counter parameter setting of Motion Sensors enrolled from
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic Powermaster-360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic Powermaster-360 in the language / languages: English as an attachment in your email.

The manual is 2.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info