769323
25
Zoom out
Zoom in
Previous page
1/96
Next page
D-307500 PowerMaster 360 Installer's Guide 25
Select MODIFY
DEVICES Option
[1]
Select the respective
device Group
[2]
Select exact device
you require to modify
[3]
Select the Parameter
you require to modify
[4]
Modify the
Parameter
02:ZONES DEVICES
CONTACT SENSORS
MODIFY SENSORS
MOTION SENSORS
Z10:Motion Camra
ID No. 140-1737
Z10:LOCATION
Z10:ZONE TYPE
Z10:SET CHIME
Z10:PARTITIONS
Z10:DEV SETTINGS
See [4]
When
done to
step 2
Modifying or Reviewing a Device
[1]
Enter the Installer Mode menu, select the 02:ZONES/DEVICES option (see section 4.2) and then select the
MODIFY DEVICES option.
[2]
Select the respective group of the device you require to review or modify. For example, MOTION SENSORS.
[3]
Scroll the Device Group, identify (by zone and/or ID number) of the exact device you require to modify or review, for
example: Z10:Motion Camra > ID No. 140-1737.
[4]
From here on the process is same as the configuration process that follows the enrollment of that device. To
continue, refer to Section 4.4.2 Adding a New Wireless Device Part B. When done, the display will show the next
device of the same type (i.e. Motion camera).
4.4.5 Replacing a device
Use this option to replace a faulty device that is enrolled in the system with another device of the same type number
(i.e. same first 3 digit of the ID number – see section 4.4.2.A) while keeping the same configuration of the original
device. There is no need to delete the faulty device or to reconfigure the new device. Once enrolled, the new device will
be configured automatically to the same configuration of the faulty (replaced) device.
To replace a device proceed as follows:
Step 1
Step 2
Step 3
Step 4
Step 5
Select REPLACE
DEVICES Option
[1]
Select the respective
device Group
[2]
Select exact device
you require to replace
[3]
Enroll the new device
[4]
02:ZONES/DEVICES
CONTACT SENSORS
REPLACE DEVICES
KEYFOBS
K03:Keyfob
ID No. 300-0307
ENROLL NOW or
ENTR ID:300-XXXX
See
[4].
Replacing a Device
[1]
Enter the Installer Mode menu, select the 02:ZONES/DEVICES option (see section 4.2) and then select the
REPLACE DEVICES option.
[2]
Select the respective group of the device you require to replace. For example, KEYFOBS.
[3]
Scroll the Device Group, identify (by zone and/or ID number) the exact device you require to replace, for example:
K03: Keyfob > ID No. 300-0307.
If you try to enroll a new device of a different type than the replaced device, the PowerMaster-360 will reject the
new device and the Virtual Keypad display will read WRONG DEV.TYPE.
When complete, the Virtual Keypad display shows the device details of the new device.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic Powermaster-360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic Powermaster-360 in the language / languages: English as an attachment in your email.

The manual is 2.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info