769323
13
Zoom out
Zoom in
Previous page
1/96
Next page
D-307500 PowerMaster 360 Installer's Guide 13
3.4 GSM connection and configuration
The GSM modem auto detection feature enables automatic enrollment of the GSM modem into the control panel
memory. GSM modem auto detection is activated after reset that is after power-up or after exiting the Installer Mode
menu. This action causes the PowerMaster-360 to automatically scan the GSM COM ports for the presence of a GSM
modem.
In the event that the GSM modem auto detection fails and the modem was previously enrolled in the control panel, the
message Cel Remvd Cnfrm is displayed on the Configurator’s Virtual Keypad. This message disappears from the
display after you press OK. The modem is then considered as not enrolled and no GSM trouble messages are
displayed.
Notes:
1) A message is displayed only when the alarm system is disarmed.
2) The GSM Alarm Transmission System is designed to comply with EN 50131-1 ATS4.
3.5 SIM card insertion
The following procedure outlines how to insert SIM card
into the GSM module, see Figure 3.1 (O):
1. Slide the top cover.
2. Open the cover.
3. Align the SIM card in the cover (note cover
orientation).
4. Slide the SIM card into the cover.
5. Rotate the cover to close.
6. Lock the cover to close.
CAUTION! Do not insert or remove the SIM card when
the control panel is powered by AC power or battery.
To configure the GSM modem, see section 4.6.2.
3.6 PowerMaster-360 prerequisites
Connection to the PowerManage server requires the following ports to be open on the router to access the internet:
TCP ports : 8080, 5001
UDP port: 5001
FTP port: 21
Note: In a typical home router these ports on the router are open.
The Configurator supports Windows 7 PC Operating System.
3.7 Enrolling and deleting a Z-Wave device
Enrolling a Z-Wave device
To enroll a device, complete the following steps:
1. Press and hold the (+) button for 2 seconds, see Figure 3.1 (J). The red LED blinks slowly, see Figure 3.1 (N).
2. Press the Enroll button on the device.
3. The green LED blinks quickly, a success beep is emitted, and the LED turns off when the device is enrolled.
Notes:
To cancel the enrollment, press and hold the (+) or (-) buttons for 2 seconds. The LED stops blinking.
If the enrollment is not successful, the red LED remains on for 3 seconds and a failure beep is emitted.
Long press on the (+) button, returns the panel to normal operation.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic Powermaster-360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic Powermaster-360 in the language / languages: English as an attachment in your email.

The manual is 2.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info