580332

Visonic PowerMaster-10-30 G2 Version 18 Manual

55
Zoom out
Zoom in
Previous page
1/74
Next page
TESTING THE SYSTEM
54 D-304829 PowerMaster-10/30 G2 User's Guide
9. Testing the System
Periodic Test
The components of your security system are designed to be maintenance-free as much as possible.
Nevertheless, it is mandatory to test the system at least once a week and after an alarm event to verify that all
system sirens, detectors, keyfobs, keypads and other peripherals function properly. Proceed as described in this
section and if there is any problem, notify your installer at once.
The test is performed in three parts:
Siren Test: Each siren of the system is automatically activated for 3 seconds (outdoor sirens with low volume).
In addition, the system tests the siren of enrolled smoke sensors.
Temperature Sensor Test: When Temperature Sensors are enrolled in the system, the control panel displays
the temperature of each zone in Celsius or Fahrenheit.
Other Device Test: Each of the other devices in the system is activated by the user and the display indicates
which devices were not yet tested. The "it's me" indication helps to identify the untested devices if necessary.
A counter also indicates the number of devices that remain untested.
Carefully read the section titled "Additional Information" according to the indicated references
1
etc –
see table at end of this section.
A. To Enter the Periodic Test Menu
1. READY 00:00
Make sure the system is disarmed and then press the button
repeatedly until the display reads "PERIODIC TEST" and press .
1
PERIODIC TEST
2.
ENTER CODE:
The screen will now prompt you to enter your user code.
3.
CODE
Enter your User Code.
2
3
☺
Go to step 4
B. To Test the Sirens
4. SIRENS TEST The display now reads [SIRENS TEST].
5.
To initiate the siren test press .
Immediately after pressing ,
all 4 LED's on the panel should light (LED test).
4
SIREN N
The display now reads [SIREN N], where "N" indicates the zone location
assigned to the siren that is currently being tested.
5
First the panel siren sounds for 3 seconds after which the PowerMaster
system will automatically repeat the procedure for the next siren enrolled in
the system until all sirens are tested.
6
You should listen to the sirens sounds and make sure that all sirens sound.
Once all the sirens have been tested, the control panel will now test the
sirens of smoke sensors that are enrolled in the alarm system. The display
now reads [Zxx: SMOKE SIREN], where "Zxx" indicates the zone number of
the smoke sensor, and alternates with [<OK> TO CONTINUE]. During this
time, the siren of the tested smoke sensor will sound for up to one minute.
Press to test the siren of the next smoke sensor.
6. SIRENS TESTS END
When all the sirens test is complete, the display reads [SIREN TESTS END].
Press the or the button to confirm the test and then move to
the next step for zone temperature display.
or
C. To Display the Temperature
7. TEMPERATURE TEST The display now reads [TEMPERATURE TEST].
8.
To display the temperature of zones on the control panel, press .
7
Z01 24.5°
°°
°C
The control panel reads the temperature of each zone. The display alternates
… 55 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic PowerMaster-10-30 G2 Version 18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic PowerMaster-10-30 G2 Version 18 in the language / languages: English as an attachment in your email.

The manual is 2,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Visonic PowerMaster-10-30 G2 Version 18

Visonic PowerMaster-10-30 G2 Version 18 Installation Guide - Dutch - 112 pages

Visonic PowerMaster-10-30 G2 Version 18 User Manual - Dutch - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info