Manual Visonic PowerMaster-10-30 G2 Version 18 (page 54 of 74) (English)

580332

Zoom out

Zoom in

1/74

SPECIAL APPLICATIONS AND FUNCTIONS

D-304829 PowerMaster-10/30 G2 User's Guide 53

8. Special Applications and Functions

Looking after People Left at Home

In addition to acting as an alarm system, the PowerMaster can also be used to monitor the movement of people

at home when the system is in the disarmed state (or even when armed “HOME” with perimeter protection only),

and report lack of motion in interior zones if there is no detection of motion within predetermined time limits.

To use this characteristic, you must ask your installer to program a specific time limit beyond which lack of

motion will be reported as a “not active” alert. For example, let us assume that an elderly, sick or handicapped

person is left unattended in a protected site. This person, disabled or sick as he may be, will not stay entirely still

for hours and is expected to wander into the kitchen to eat or drink, or to the bathroom for other necessities.

Upon doing so, the bedroom, bathroom and kitchen motion detectors will detect his movement.

Important!

To enable motion detectors to function during the disarmed state, all motion detectors must be configured by the

installer to detect activity during disarmed state (i.e. "DISARM Activity" recommended setting ""YES + 5m delay").

For further details, refer to the motion detector's Installation Instructions.

If, for example, the “lack of motion” time limit is set by your installer to 6 hours, a virtual 6-hour clock will carry

out a 6-hour “countdown”.

If motion is detected within the 6-hour time frame, the countdown will restart from the beginning (the virtual 6-

hour clock will be “reset”) and no alert message will be sent out.

If no motion is detected within the 6-hour time frame in any interior zone, the control panel will send a “not-

active” alert message to the monitoring station or to private telephones designated by the installer.

Note: Tracking inactivity of elderly (Looking after People Left at Home) not to be enabled in UL Listed product.

Acknowledging “low battery” condition in Keyfobs

Some regulations and institutions require the user to acknowledge when the keyfob enters the “low battery”

condition. In such cases the installer will program the system to operate as follows:

If you try to disarm the system with a keyfob whose battery voltage is low, a protest beep will be heard for 15

seconds. During this period you should press again the disarm button of the keyfob or control panel (for the

control panel, a user code is required) to disarm the system. If you perform this action during the 15 seconds

period, a Low Bat acknowledge message will be stored in the event log.

If the disarm button is not pressed again during the 15 seconds period you will not be able to rearm the system

unless you perform either one of the following actions:

A. Press AWAY twice to arm the system.

B. Press AWAY and then press disarm button.

Performing either of these two actions will also store the acknowledge message in the event log.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Visonic PowerMaster-10-30 G2 Version 18 in the language / languages: English as an attachment in your email.

The manual is 2,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Visonic PowerMaster-10-30 G2 Version 18

Visonic PowerMaster-10-30 G2 Version 18 Installation Guide - Dutch - 112 pages

Visonic PowerMaster-10-30 G2 Version 18 User Manual - Dutch - 72 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Visonic PowerMaster-10-30 G2 Version 18 Manual

Product: