580332
51
Zoom out
Zoom in
Previous page
1/74
Next page
EVENT REPORTING & CONTROL BY TELEPHONE AND SMS
50 D-304829 PowerMaster-10/30 G2 User's Guide
Event notifications by SMS
Note: This feature is not to be not to be enabled in UL Listed product.
The PowerMaster system when equipped with a GSM unit can be programmed to send SMS event notification
messages to 4 pre-selected telephone numbers - see Chapter – 6, B.11. The messages can be tagged with a
"House ID" name, for example, "JOHN'S HOUSE", see Remote Control by SMS section, command no. 10.
Example of the reported SMS messages:
JOHN’S HOUSE
**AWAY**
JOHN’S HOUSE
**DISARM**
JOHN’S HOUSE
POWERMASTER: LOW BATTERY
GARAGE: LOW BATTERY
JOHN’S HOUSE
STATUS MESSAGE 01
(Event list is displayed)
Note: Status messages can be sent only to a calling telephone whose identity number is not blocked by the user!
Remote Control by Telephone
Note: This feature is not to be not to be enabled in UL Listed product.
The PowerMaster allows you to initiate calls from your private telephone to the PowerMaster control panel via
PSTN (landline) or GSM and to perform a variety of arming commands remotely using your telephone's keypad.
To connect to the PowerMaster when the PowerMaster is connected to the PSTN:
1. Dial the PowerMaster PSTN tel. No.
2. Wait for 2-4 rings then hang up.
1
3. Wait 12-30 sec.
4. Redial PowerMaster tel. No. (sound will be heard for 10 sec.).
5. [*] (to stop the sound)
6. [User code], [#]
2
7. [Desired command]
To connect to the PowerMaster when the PowerMaster is connected to the GSM:
1. Dial the PowerMaster GSM tel. No. (sound will be heard for 10 sec.)
2. [*] (to stop the sound)
3. [User code], [#]
2
4. [Desired command]
Notes:
(1) Entering of user code is required once only.
(2) If you wait more than 50 seconds (may change according to setup / use) without keying a command, the
PowerMaster will disconnect the line.
A. Executable Commands
Command Single Partition Keying
Sequence
All Partitions Keying Sequence
1
Disarming
[]
[1]
[#] []
[0]
[partition]
[1]
[#]
2
Arming Home
[]
[2]
[#] []
[0]
[partition]
[2]
[#]
3
Arming Home-Instant
[]
[2]
[
1]
[#] []
[0]
[partition]
[2]
[
1]
[#]
4
Arming Away
[]
[3]
[#] []
[0]
[partition]
[3]
[#]
5
Arming Away-Instant
[]
[3]
[1]
[#] []
[0]
[partition]
[3]
[1]
[#]
6
Arming Away-Latchkey
[]
[4]
[#] []
[0]
[partition]
[4]
[#]
7
Arming Away-Instant-Latchkey
[]
[4]
[
1]
[#] []
[0]
[partition]
[4]
[
1]
[#]
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic PowerMaster-10-30 G2 Version 18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic PowerMaster-10-30 G2 Version 18 in the language / languages: English as an attachment in your email.

The manual is 2,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Visonic PowerMaster-10-30 G2 Version 18

Visonic PowerMaster-10-30 G2 Version 18 Installation Guide - Dutch - 112 pages

Visonic PowerMaster-10-30 G2 Version 18 User Manual - Dutch - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info