667227
40
Zoom out
Zoom in
Previous page
1/352
Next page
0478 111 9924 C - EN
38
Hold the canister (3) steady and pour in
the fuel carefully in several stages up to
approx. 4 cm below the edge of the fuel
tank.
The more fuel has already been filled
into the tank, the smaller the filling
quantities should be for each filling
operation.
Keep checking the filling level of the
tank at regular intervals while filling the
tank; remove the funnel for this
purpose.
Screw the tank cap (1) back on again.
8.1 General
Place the machine on level and firm
ground when performing all the
operations described.
8.2 Height adjustment of the
handlebar
The height of the handlebar can be
individually adjusted.
Loosen nuts (1) and (2).
Adjust the handlebar to a pleasant
operating height by moving it upwards
or downwards and hold it in position.
Tighten the nuts (1) and (2) again.
8.3 Folding down the handlebar
The handlebar can be folded down
for space-saving transport and
storage of the mower.
Stop the engine and remove the spark
plug socket. (Ö 11.2)
Detach the recoil starter rope. (Ö 8.4)
MB 4 R, MB 4 RT:
Hold the handlebar (1), open the left
and right quick-clamping devices (2)
and carefully fold the handlebar
downwards to the front.
MB 4 RTP:
Hold the handlebar (1), loosen the left
and right nuts (2) and carefully fold the
handlebar downwards to the front.
8.4 Attaching and detaching the
recoil starter rope
Attaching
Detach the spark plug socket from the
engine.
Press the motorstop lever (1) to the
handlebar and hold.
Slowly pull out the recoil starter
rope (2).
Release the motorstop lever (1) and
attach the recoil starter rope (2) to the
rope guide (3).
Connect the spark plug socket.
Detaching
Detach the spark plug socket from the
engine.
Detach the recoil starter rope (2) from
the rope guide (3).
8.5 Cutting height adjustment
Five different cutting heights can be set.
The highest cutting level
(70 mm) is selected when the
cutting height adjustment
lever is in the rearmost
position (see marking).
The lowest cutting level (30 mm) is
selected when the cutting height
adjustment lever is in the frontmost
position.
Press the cutting height adjustment
lever (1) outwards towards the rear
wheel and hold in position.
Set the cutting height adjustment
lever (1) to the required position in the
detent segment (2) and allow it to
engage.
8. Controls
Risk of injury!
Observe the safety instructions in
the section "For your safety" (Ö 4.).
10
Danger of pinching!
The handlebar can fold down or
retract inadvertently when the
quick-clamping device/handlebar
screw fastening is released.
For this reason, always hold the
handlebar with one hand when you
release the fastening.
11
12
13
Risk of injury!
Stop the engine before adjusting
the cutting height.
14
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking MB 4RT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking MB 4RT in the language / languages: All languages as an attachment in your email.

The manual is 21,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info