667219

Viking MB 2R Manual

38
Zoom out
Zoom in
Previous page
1/424
Next page
0478 111 9926 C - EN
36
1 Setting the rear cutting height
● Set the required cutting height at the
rear axle (1).
For this purpose, support the machine
with one hand and move the rear axle to
the desired level on one side first and
then on the other.
Ensure that the left and right sides are
at the same level (rear axle parallel to
the housing).
2 Setting the front cutting height
● MB 2 RT:
Push the cutting height adjustment
lever (2) outwards, move to the desired
level and allow it to engage.
● MB 2 RC, MB 2 R:
Set the required cutting height at the
front axle (3).
For this purpose, support the machine
with one hand and move the front axle
to the desired level on one side first and
then on the other. Ensure that the left
and right sides are at the same level
(front axle parallel to the housing).
The machine is equipped with several
safety devices for safe operation and for
the prevention of improper use.
9.1 Motorstop lever
The lawn mower is equipped with a
motorstop device.
The engine stops when the motorstop
lever is released during running operation.
The engine and blade come to a standstill
within 3 seconds.
Measuring the run-on time
Following engine start-up, the blade
rotates and a wind noise is audible. The
run-on time corresponds to the duration of
the wind noise after the engine stops. This
can be measured using a stopwatch.
10.1 General information on mulching
During mulching, the cut grass is chopped
up several times through a special air flow
guidance system in the mower blade area
and then blown back into the turf. The
clippings remain on the lawn.
Benefits
The decomposing clippings return organic
nutrients to the soil, serving as a natural
fertiliser.
Advantages
Emptying the grass catcher box and
disposal of the clippings are dispensed
with. Weed growth is slowed down and
significant amounts of fertilizer are saved.
10.2 When is mulching permissible?
VIKING recommends mulching only when
the lawn is dry and the grass is not too
high.
If the grass is too high, the lawn should be
mowed in two stages. (Ö 10.3)
10.3 How should mulching be
performed?
Requirements for good mulching results:
– Set the optimal cutting height: A third of
the grass height should be cut.
– Use well sharpened blades.
– Vary the mowing direction and ensure
that the mowing strips overlap.
Working method in high grass
In high grass, the lawn should be cut in two
stages.
First stage:
The lawn is mowed at the maximum
cutting height.
Second stage:
12 to 24 hours after the first stage, mulch
the lawn to the desired grass height at right
angles to the first mowing direction.
9. Safety devices
Risk of injury!
If a safety device is found to be
defective, the machine must not be
operated. Consult a specialist
dealer; VIKING recommends
VIKING specialist dealers.
Risk of injury!
If the run-on time of the blade
exceeds this delay, stop using the
machine and take it to your
specialist dealer.
10. Notes on working with
the machine
Caution
If the cutting height is too low or the
grass is wet, the housing may
become clogged, blocking the
blade!
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking MB 2R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking MB 2R in the language / languages: All languages as an attachment in your email.

The manual is 23,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info