667219
37
Zoom out
Zoom in
Previous page
1/424
Next page
35
DEFRNLITESPTNOSVFIDAPLHUSRHR EN
0478 111 9926 C - EN
Tighten the pre-installed quick-
clamping devices (2) (they should
project by about one screw thread turn)
and fold upwards.
Check correct assembly
The quick-clamping devices (1)
must be sufficiently tightened so
that they are pressed tightly against the
handlebar and the upper handlebar is
firmly connected to the lower
handlebar.
If the handlebar is not firmly installed or
the quick-clamping devices are not
correctly located, fold open the quick
clamping devices and adjust them to
the correct position by screwing out and
back in again.
Check that the cables (2, 3) and the
cable clip (4, MB 2 RC) are in the
correct position.
7.3 Fuel and engine oil
Engine oil:
Please consult the engine
instruction manual for the type of
engine oil to be used and the oil capacity.
Check the oil filling level at regular
intervals (see engine instruction manual).
Avoid exceeding or falling below the
correct oil level.
Screw on the oil tank cap properly before
operating the engine.
Fuel:
Recommendation:
Fresh good quality fuels,
unleaded petrol.
Please consult the engine instruction
manual for details on the fuel quality
(octane rating).
8.1 General
Place the machine on level and firm
ground when performing all the
operations described.
8.2 Folding down the handlebar
The handlebar can be folded down
for space-saving transport and
storage of the mower.
Stop the engine and remove the spark
plug socket. (Ö 11.2)
Detach the recoil starter rope. (Ö 8.3)
Open the left and right quick-clamping
devices (1) and carefully fold the
handlebar (2) downwards to the front.
8.3 Attaching and detaching the
recoil starter rope
Attaching
Detach the spark plug socket from the
engine.
Press the motorstop lever (1) to the
handlebar and hold.
Slowly pull out the recoil starter
rope (2).
Release the motorstop lever (1) and
attach the recoil starter rope (2) to the
rope guide (3).
Connect the spark plug socket.
Detaching
Detach the spark plug socket from the
engine.
Detach the recoil starter rope (2) from
the rope guide (3).
8.4 Adjusting the cutting height
There are 4 different cutting height settings
from 28 mm to 85 mm.
Level 1 = lowest cutting height
Level 4 = highest cutting height
Avoid damage to the machine
Top up engine oil before starting for
the first time. Use a suitable filling
aid when topping up the engine oil
and when refuelling (e.g. funnel).
4
5
8. Controls
Risk of injury!
Observe the safety instructions in
the section "For your safety" (Ö 4.).
Danger of pinching!
The handlebar can fold down
uncontrollably when the quick-
clamping devices are released.
For this reason, always hold the
handlebar with one hand when you
release the fastening.
6
Risk of injury!
Stop the engine before adjusting
the cutting height.
Risk of injury!
The setting on the front and rear
axles must be identical.
7
8
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking MB 2R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking MB 2R in the language / languages: All languages as an attachment in your email.

The manual is 23,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info