667223

Viking MB 248T Manual

40
Zoom out
Zoom in
Previous page
1/269
Next page
0478 111 9922 B - EN
38
Cleaning position:
● Select cutting level 1. (Ö 7.7)
● Release the upper handlebar (1) by
unscrewing the two rotary handles (2).
● Open the discharge flap and hold it
open.
● Place the machine in the cleaning
position until it stands on its own.
11.3 Engine
Maintenance interval:
See engine instruction manual.
General information:
Observe the operating and maintenance
instructions contained in the attached
engine instruction manual.
To achieve a long service life, it is always
particularly important to maintain a
sufficient level of oil and to change the oil
and air filter regularly.
The recommended oil change intervals as
well as information on engine oil and oil
capacities can also be found in the engine
instruction manual.
The cooling ribs must always be kept clean
to ensure that the engine is adequately
cooled.
11.4 Checking the mowing blade
wear limit
Maintenance interval:
Before each use.
Check procedure:
The mowing blade (1) must be cleaned
thoroughly before each check procedure.
● Place the machine in the cleaning
position. (Ö 11.2)
Mowing blade thickness:
The blade thickness (A) must be at least
2mm at any point. The most important
points are marked in the illustration.
(Check using slide calliper).
Wear limit of the cutting edges:
The cutting edges must not be ground
back by more than 5mm (distance (B))
during sharpening. When checking, place
a ruler (2) against the front blade edge (3)
and check for wear.
11.5 Maintaining the mowing
blade
Removing the mowing blade:
For removal, use a wooden block (1)
(approx. 60 x 60 mm) to counterhold the
mowing blade (2).
● Loosen and unscrew the blade
fastening screw (3). Remove the blade
fastening screw (3), washer (4) and
mowing blade (2).
Sharpening the mowing blade:
● Cool the mowing blade when
sharpening, e.g. with water. The blade
must not be allowed to display blue
colouring, as this would reduce its
cutting quality.
● Sharpen blades evenly to prevent
vibration due to imbalance.
● The cutting angle of 30° must be
observed.
Risk of injury!
Stop the engine and remove the
spark plug socket.
Empty the fuel tank (run empty)
before placing the machine in the
cleaning position.
Risk of injury!
Observe the safety instructions in
the "For your safety" section. (Ö 4.)
Risk of injury!
A worn mowing blade may break
off and cause serious injuries. The
instructions for blade maintenance
must therefore always be
observed.
Mowing blades are subject to
differing degrees of wear
depending on the location and
duration of use. If you use the
machine on sandy ground or use it
frequently under dry conditions, the
mowing blade will be subjected to
greater loads and will wear more
quickly than the average.
14
Risk of injury!
Observe the safety instructions in
the section "For your safety". (Ö 4.)
We recommend that you have the
mowing blade sharpened by a
specialist dealer.
Risk of injury!
Always wear safety glasses and
gloves when sharpening.
15
… 40 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking MB 248T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking MB 248T in the language / languages: All languages as an attachment in your email.

The manual is 11,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info