813781
36
Zoom out
Zoom in
Previous page
1/112
Next page
36
Note
The DHW is not heated between the time phases.
Only frost protection for the DHW cylinder is active.
When setting time programs, bear in mind that your
heating system requires some time to heat the DHW
cylinder to the required temperature. Select a corre-
spondingly earlier start time. Use the "Start optimi-
sation" and "Stop optimisation" functions: See
pages 36 and 36.
Your rooms will not be heated whilst the DHW cylin-
der is being heated.
Operating status for DHW heating
The operating statuses for DHW heating differ as fol-
lows depending on the type of DHW cylinder you have
installed:
DHW cylinder with one temperature sensor at the
top
"Top"
The top section of the DHW cylinder is heated to the
"Set DHW temperature", e.g. when there is little
DHW demand: See page 35.
"Standard"
The top section of the DHW cylinder is heated to the
"Set DHW temperature": See page 35.
"Temp. 2"
The top section of the DHW cylinder is heated to the
"Set DHW temperature 2": See page 35.
DHW cylinder with two temperature sensors
Applies to the following versions:
DHW cylinder with temperature sensors at the top
and bottom
Heat pump with integral DHW cylinder
"Top"
The top section of the DHW cylinder is heated to the
"Set DHW temperature", e.g. when there is little
DHW demand: See page 35.
"Standard"
The entire volume of the DHW cylinder is heated to
the "Set DHW temperature": See page 35.
"Temp. 2"
The entire volume of the DHW cylinder is heated to
the "Set DHW temperature 2": See page 35.
Note
Your contractor will have listed the equipment and
functions of your heating system in the form on
page 102.
For questions relating to the scope of and accessories
for your heat pump and your heating system, contact
your contractor.
Setting start optimisation
Start optimisation ensures that DHW is available at the
set temperature at the beginning of a time phase in the
time program.
1. Extended menu:
2. "DHW"
3. "Start optimisation"
Example:
From 06:00 h, hot water for showering is required.
Set the start of the time phase in the time program to
06:00 h. With start optimisation, DHW heating starts
automatically earlier than this.
This makes DHW available at the set temperature at
06:00 h.
Setting stop optimisation
The stop optimisation ensures that the DHW cylinder is
always fully heated at the end of the time phase in
accordance with the time program.
1. Extended menu:
2. "DHW"
3. "Stop optimisation"
DHW heating
Setting the time program for DHW heating (cont.)
5817913
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viessmann VITOTRONIC 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viessmann VITOTRONIC 200 in the language / languages: English as an attachment in your email.

The manual is 3.87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Viessmann VITOTRONIC 200

Viessmann VITOTRONIC 200 User Manual - German - 112 pages

Viessmann VITOTRONIC 200 User Manual - Dutch - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info