652089

Viessmann 5243 Manual

9
Zoom out
Zoom in
Previous page
1/16
Next page
9
Anschluss von LEDs
Die Funktionsausgänge des Lokdecoders schal-
ten gegen Decodermasse. Daher müssen am
AusgangderFunktionsausgängedieKathoden(-)
der LEDs ange schlossen werden.
Beachten Sie:
WennSieLEDseinsetzen,müssenSiedie-
seimmerübereinenVorwiderstandbetrei-
ben!DieVorwiderständesindjenachStrom
und Bauform der Leuchtdioden unterschied-
lich. Ermitteln Sie die richtigen Werte oder
erfragen Sie sie beim Kauf.
SiekönnenmehrereLEDsaneinenAusgangpar-
allelanschließen.DabeibenötigtjedeDiodeeinen
eigenenVorwiderstand.WennSiemehrereLEDs
aneinenAusganginReiheanschließen,reichtein
Vorwiderstandaus.
Befestigung des Lokdecoders
Decoder mit Schnittstellenstecker sind durch den
Stecker bereits hinreichend befestigt.
Nach Fertigstellung aller Anschlüsse sollten Sie
denLokdecoder5242befestigen.Dieskannz.B.
mit doppelseitigem Klebeband erfolgen.
5. Programmierung
BevorSiemitdemProgrammierendesLokdeco-
dersbeginnen,mussderMotorandenDecoder
angeschlossensein,dasonstkeineRückmeldung
zur(DCC-)Zentraleerfolgenkann.
WennSiedenDecodermiteinerMotorola-Zentra-
leprogrammierenwollen,solltenSieandieAus-
gängeAUX1undAUX2Beleuchtungenanschlie-
ßen,dadieLokdenWechselindenProgrammier-
modusunddieÜbernahmederEingabendurch
das Blinken der Beleuchtung an diesen Ausgän-
gen quittiert.
ImDCC-FormatkönnenRegisteroderKongu-
rationsvariablen(CVs)programmiertwerden.Die
Hauptgleisprogrammierungistebenfallsmöglich.
ImMotorola-FormatwerdendieEinstellungenin
Registerprogrammiert.
Programmierung mit DCC-Zentralen
VonderZentraleauskönnenSiedieKongurati-
onsvariablen(CVs)desDecodersprogrammieren.
BeachtenSiedazudenbetreffendenAbschnittin
derBedienungsanleitungIhrerZentrale,inderdie
byteweiseProgrammierungderCV-Variablenbe-
schriebenist.MitZentralen,dielediglichdieRe-
gister-Programmierungermöglichen,könnenSie
nurdieVariablenCV#1,CV#2,CV#3,CV#4und
CV#29(=Register1bis5)programmieren.
youmustconnectthecathode(-)oftheLEDto
the function outputs.
Caution:
Ifyouuselight-emittingdiodes(LEDs)you
mustalwaysoperatethemviaaseriesre-
sistor.LEDsareavailableinmanydiffer-
entmodels.Theseriesresistorlimitsthe
currentowoftheLEDandwillneedtobe
calculatedforeachmodel.Askforthemax.
currentratingwhenbuyingyourLEDs.
YoucanconnectseveralLEDsinparalleltoeach
output.InthiscaseeveryLEDmusthaveaseries
resistorofitsown.IfyouconnectseveralLEDs
tooneoutputinseries,onlyoneseriesresistoris
needed.
Fixing the locomotive decoder
DecoderwithinterfacesocketasperNEM651
arexedcorrectbythesocketanddon’tneeda
furtherxation.
Aftercompletingallconnectionsxthelocomotive
decoder5242withdouble-sidedadhesivetape,
forexample.
5. Programming
Beforestartingtoprogramthelocomotivedecoder
youshouldconnectthemotortothedecoder.
Otherwisethereisnoconrmationsignalfromthe
(DCC-)centralunit.
Shouldyouintendtoprogramthedecoderwitha
Motorolacentralunityoushouldalwaysconnect
thelightingtotheoutputsAUX1andAUX2.The
locomotiveindicatesthechange-overtothepro-
grammingmodeandthetaking-overofsettingsby
ashingofthelightingconnectedtotheseoutputs.
InDCCformatitispossibletoprogramregisteror
congurationvariables(CVs),maintrackprogram-
mingcanbeusedaswell.InMotorolaformatthe
settingsaresavedinregisters.
Programming with DCC central units
Youcanprogrammthecongurationvariables
(CV)ofthedecoderfromthedigitalcentralunit.
Seethechapterinthemanualofyourcentralunit
wherethebytewiseprogrammingofconguration
variables(CVs)isexplained.Withcentralunits
thatallowonlyregister-programmingitisonlypos-
sibletoprogramthevariablesCV#1,CV#2,CV#3,
CV#4andCV#29(=register1to5).
Programming with the Central Station
and the Mobile Station
WiththeCentralStationortheMobileStationof
Märklin**youcanprogramtheregisters,butthe
valuetobesetislimitedto80.Selectthearticle
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viessmann 5243 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viessmann 5243 in the language / languages: English, German as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info