652086
7
Zoom out
Zoom in
Previous page
1/8
Next page
7
nun bereit, eine DCC-Adresse zu empfangen
und als eigene zu speichern.
4. Per Digitalzentrale die gewünschte DCC-Digi-
taladresse durch Druck auf die entsprechende
Taste / Schaltäche senden.
Der Decoder empfängt den Befehl, registriert
die Adresse und quittiert dies durch Bewegung
der Weiche an Ausgangsgruppe 1.
Damit ist der Decoder unter der neuen Adresse
betriebsbereit. Falls Sie die Adresse künftig än-
dern möchten, wiederholen Sie die Prozedur ein-
fach.
MM-Digitaladresse zuweisen:
1. Decoders gemäß Abb. 2 anschließen (inkl. eine
Weiche an Ausgangsgruppe 1).
2. Digitalsystem einschalten.
3. Roten Taster am Decoder einmal drücken.
Die an Ausgang 1 angeschlossene Weiche
schaltet langsam hin und her.
4. Roten Taster am Decoder
ein zweites Mal drücken.
Die an Ausgang 1 angeschlossene Weiche
schaltet schnell hin und her. Der Decoder ist
nun bereit, eine MM-Adresse zu empfangen
und als eigene zu speichern.
5. Per Digitalzentrale die gewünschte MM-Digital-
adresse durch Druck auf die entsprechende Ta-
ste / Schaltäche senden. Der Decoder emp-
fängt den Befehl, registriert die Adresse und
quittiert dies durch Bewegung der Weiche an
Ausgangsgruppe 1.
Damit ist der Decoder unter der neuen Adresse
betriebsbereit. Falls Sie die Adresse künftig än-
dern möchten, wiederholen Sie die Prozedur ein-
fach.
Adress-Einstellungsmodus verlassen
ohne Änderung:
Mit einem dritten Druck auf den roten Taster des
Decoders verlassen Sie ohne Veränderung der
Adresse den Adress-Programmiermodus.
Hinweis:
Der Decoder lässt sich nur auf eine Gruppe
von 4 aufeinanderfolgenden Weichenadressen
programmieren, z. B. 1 - 4, 5 - 8, 9 - 12. Es ist
also nicht möglich, den Decoder auf die Adres-
sen 3 - 6 zu programmieren, da diese Adres-
sen zwei verschiedenen Gruppen angehö-
ren. Welche Taste innerhalb der Vierergruppe
Sie bei der Programmierung drücken, ist völlig
gleich. Alternativ können Sie auch einen Wei-
chenschaltbefehl über ein Modellbahn-Steue-
rungsprogramm Ihres Computers (WIN-DIGI-
PET) auslösen.
ready to receive a DCC address and to store it.
4. Transmit the desired digital address by push-
ing the corresponding buttons on the com-
mand station. The decoder receives the com-
mand, registers the address and conrms this
by switching the turnout wired to output 1.
Then the decoder is ready for operation with its
new address. Should you wish to change the ad-
dress at a later stage simply repeat this procedure
and enter the new address.
Assigning an MM digital address:
1. Wire the decoder according to Figure 2 (includ-
ing a turnout on output group 1).
2. Turn on the digital system.
3. Press the red button on the decoder once.
The turnout wired to output 1 will switch slowly
forwards and backwards.
4. Press the red button on the decoder
once more.
The turnout wired to output 1 switches quickly
forwards and backwards. The decoder is now
ready to receive an MM address and to store it.
5. Transmit the desired digital MM address by
pushing the corresponding buttons on the com-
mand station. The decoder receives the com-
mand, registers the address and conrms this
by switching the turnout wired to output 1.
6. Then the decoder is ready for operation with its
new address. Should you wish to change the
address at a later stage simply repeat this pro-
cedure and enter the new address.
Exiting the address setting mode
without programming or changing an
address:
With a third press of the red button you can exit
the address programming mode without having
programmed an address.
Note:
The decoder can only be programmed to a
group of four consecutive addresses e.g.: 1
– 4, 5 - 8, and 9 - 12. It is not possible to pro-
gram the decoder for instance to the addres-
ses 3 – 6 since these addresses belong to two
different groups of addresses. It is unimportant
which button you press within the group of four
for programming the address. Alternatively you
may also activate a switching command for a
turnout or signal with a train control software
running on your PC e.g.: WIN-DIGIPET.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viessmann 5212 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viessmann 5212 in the language / languages: English, German as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info