652086
5
Zoom out
Zoom in
Previous page
1/8
Next page
5
DCC-
Magnetartikeldecoder
5212
Viessmann
Adresse
+
+
+
+
~~
J K 1
E
gnrt
4 3
2 gnrt
gnrtgn rt
5,6 / 1W
z. B. 5212
Minitrix-Weiche
grün
gelb
weiß
Widerstand
e. g. 5212
Minitrix turnout
/ green
/ yellow
/ white
resitor
Fig. 2
Abb. 2
DCC-
Magnetartikeldecoder
5212
Viessmann
Adresse
+
+
+
+
~~
J K 1
E
gnrt
4 3
2 gnrt
gnrtgn rt
5212
Digitalzentrale
schwarz
rot
Digital Command Station
/ black
/ red
Fig. 3
Abb. 3
Schließen Sie das Modell gemäß der Beispiele
auf Seite 4 bis 6 an.
Wichtiger Hinweis für Minitrix-Anwender!
Bei Verwendung von Weichenantrieben der
Marke Minitrix kann es zu Schaltversagen
kommen, da diese im Schaltmoment eine
Stromaufnahme von 2,2 Ampere haben! Die
Überlastsicherung des Decoders blockiert den
Schaltbefehl.
Lösung (siehe Abb. 3):
1. Schließen Sie die „E“-Buchse jedes Deco-
ders an einem Viessmann-Powermodul 5215
an (ein Powermodul reicht für alle angeschlos-
senen Decoder aus). Dieses Powermodul ver-
sorgen Sie mit 16 Volt Wechselspannung, wie
sie vom Viessmann-Lichttransformator 5200
geliefert wird.
2. Schalten Sie in die weiße Zuleitung (ge-
meinsamer Pol beider Antriebsspulen) jeder
Minitrixweiche, welche am gelben (mittleren)
Pol der Ausgangsbuchsen-Dreiergruppen des
Magnetartikeldecoders angeschlossen wird,
einen Widerstand von 5,6 Ohm und einer Lei-
stung von 1 W.
Wire the module according to the examples
shown on pages 4 to 6.
Important note for Minitrix users!
When using Minitrix turnout motors switching
may not be reliable since these motors draw
2.2 Amps! The overload protection of the deco-
der therefore blocks the switching command.
Potential solution (refer to Figure 3):
1. Wire the “E” socket of each decoder to a
Viessmann Power Module 5215 (one Po-
wer Module is sufcient for all connected de-
coders). The Power Module provides 16 Volt
AC as is the case with the Viessmann lighting
transformer 5200.
2. Wire a 5.6 Ohm resistor with a power rating
of 1 Watt into the white wire connected to the
yellow socket of the decoder (centre socket of
each output pair) for all Minitrix turnout motors.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viessmann 5212 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viessmann 5212 in the language / languages: English, German as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info