785523
8
Zoom out
Zoom in
Previous page
1/25
Next page
4. Installation
This product should be installed by a qualified electrician.
4.1. Location
The product must be installed in a dry and well-ventilated area, as close as possible to the batteries. There should be a clear
space of at least 10cm around the appliance for cooling.
1. Excessively high ambient temperature will result in the following:
Reduced service life
Reduced charging current.
Reduced peak capacity, or shutdown of the inverter.
2. Never mount the product directly above the batteries.
For mounting see G
For safety purposes, this product should be installed in a heat-resistant environment. Prevent the presence of
e.g. chemicals, synthetic components, curtains or other textiles, etc., in the immediate vicinity.
4.2. Connection of the Battery cables
NO internal DC Fuses.
In order to fully utilize the full capacity of the product, batteries with sufficient capacity and battery cables with sufficient cross
section should be used. See table below:
12/2000/80 24/2000/50 48/2000/25
Recommended battery capacity (Ah) 350-1000 200–500 100-250
Recommended DC fuse 300A 200A 100A
Recommended cross section (mm2)
per + and - connection terminal
0 – 5 m 70mm-2 35 mm2 25 mm2
5 – 10 m 95mm2 70 mm2 50mm2
Remark: Internal resistance is the important factor when working with low capacity batteries. Please consult your supplier or the
relevant sections of our book ‘Energy Unlimited’, downloadable from our website.
Procedure
Proceed as follows to connect the battery cables:
Use a torque wrench with insulated box spanner in order to avoid shorting the battery.
Recommended torque: 12 Nm (M8 nut)
Avoid shorting the battery cables.
Undo the two screws at the bottom of the enclosure and remove the service panel.
Connect the battery cables: see Appendix A.
Tighten the nuts well for minimal contact resistance.
All servicing must be undertaken by qualified personnel.
4.3. Connection of the AC cabling
This is a Safety Class I product (supplied with a protective grounding terminal). Uninterruptible protective
grounding must be provided at the AC input and/or output terminals and/or chassis grounding point
located externally on the product.
MultiPlus 2kVA 230V
Page 6 Installation
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Victron MultiPlus 12 2000 80-32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Victron MultiPlus 12 2000 80-32 in the language / languages: English as an attachment in your email.

The manual is 1.31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info