785236
27
Zoom out
Zoom in
Previous page
1/59
Next page
Item Default Description
Show mobile overview No Enable this to show the mobile overview page which is designed for Marine and Remote Vehicle
applications. This overview gives direct access to the AC Current limit as well as the On/Off/
Charger-only settings and pump control. Also shows up to four tank levels.
Language English Choose between English, Dutch, Chinese, German, Spanish, French, Italian, Swedish, Turkish
and Arabic.
VRM online portal
Logging enabled Enabled
VRM Portal ID
Log interval 15 minutes Set to anything between 1 minute and 1 day. Choose longer times on systems with an unreliable
connection. Note that this setting does not affect reporting problems and state changes (bulk →
absorption) to the VRM Portal. These events initiate an immediate transmission of all parameters.
Use secure connection (HTTPS)
Last contact
Connection error
Reboot device when no contact
Storage location
Rest of parameters See section 5.3, Datalogging to VRM, for more details
Wireless AC Sensors
Select the position for each AC sensor (PV Inverter on AC-input 1, 2 or on AC-output). More information about the Wireless AC sensors.
Energy meters
Configure the Energy meters, used for one of three things:
Measure the output of a PV Inverter
Measure and regulate a Hub-4 system
Measure and regulate a ESS system
Measure the output of an AC Generator.
ESS
Configure Energy storage system (ESS) ESS system.
PV inverters
Inverters
Find PV inverters
Detected IP addresses
Add IP address manually
Automatic scanning
Wireless AC sensors
Ethernet
Select the configuration type (DHCP vs. manual configuration) and IP settings.
Wi-Fi
Manage wireless networks and IP settings.
GSM modem
GPS
GPS information Status, Latitude, Longitude, Speed, Course, Altitude, Number of satellites
Format Select the format in which to show the Latitude and Longitude.
Speed unit km/h Choose between km/h, meters per second, miles per hour, or knots.
Device
Generator start/stop
Configure generator autostart settings and conditions. GX - Generator auto start/stop
Tank pump
Configure automatic starting and stopping of pump based on tank level(sender) information. Pump auto start/stop with Color Control GX
Relay
Function Alarm relay Select the relay function. Possible functions are 'Alarm relay', 'Generator start/stop', 'Tank pump'
and 'None' (disabled).
Polarity Normally open Select the polarity of the relay on the back of the Cerbo GX. 'Normally open' or 'Normally closed'.
(Note that setting it to normally closed increases the Cerbo GX power draw.)
Services
ModbusTCP Off This setting enables the ModbusTCP service. More information about ModbusTCP in this docu-
ment: https://www.victronenergy.com/upload/documents/Whitepaper-Data-communication-with-
Victron-Energy-products_EN.pdf
MQTT on LAN (SSL) On
MQTT on LAN (Plaintext) Off
VRM two-way communication No Enable remote configuration and firmware updates. VE Power Setup manual
Bluetooth On
Cerbo GX Manual
27
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Victron Cebro GX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Victron Cebro GX in the language / languages: English as an attachment in your email.

The manual is 5.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info