484572

Vibiemme Vibiemme Double Domobar version 3 Manual

69
Zoom out
Zoom in
Previous page
1/74
Next page
63
Troubleshooting
1 •
The machine is not working at all and no lights come on.
Be sure it is plugged in and the circuit into which it is plugged is working. Try another outlet if in doubt.
Try an outlet on a circuit that powers no other electrical appliances. Check the voltage of the circuit while the
DD is in operation. Be sure that the PID is on (see Chapter 12) and that the power switch is in “Position I” or
“Position II.”
2 • I hear the pump but no water comes out
Rotary pumps are designed to receive water from a pressurized source. You may need to prime the pump
if you are not using the plumbed option and a situation such as one of the following has taken place:
•
You are using the reservoir for the first time
•
You haven’t used the reservoir for a while (such as a plumbed machine being descaled)
•
You ran the reservoir out of water
•
The reservoir pik up hose came out of the water and pulled in air
Follow these directions to prime the pump:
1 Be sure that the water selector valve is switched to the reservoir position (pointing to your LEFT when
looking under the machine from the front)
2 Lift the hose out of the reservoir and remove the filter from the end of the hose.
3 Hold the hose straight up and using a suitable tool (turkey baster, syringe, or small funnel for example)
completely fill the hose with water.
4 While still holding the filled hose upwards in one hand, turn the power switch to “Position 1” and lift the
brew lever all the way. Almost immediately, the water in the hose should be drawn into the pump. As soon
as the water level in the hose begins to recede, immediately lower the brew lever fully and turn the
power switch to “Position 0.” If the water is not drawn in you may need to force the water with some pres
-
sure into the hose while the pump is running. A large size syringe or equivalent tool can be used.
5 Replace the filter on the end of the hose and lay the filter flat on the bottom of reservoir.
6 Turn the power switch to “Position I” and lift the brew lever. The pump should now be drawing water from
the reservoir and a flow of water should come from the group.
3 • The brewing temperature is too hot or too cold.
Use the information in Chapter 12 and verify that the PID Offset Temperature has been correctly adjusted
to match the temperature measurement standard you have chosen (the correct offset is 19 for Fahrenheit and
10 for centigrade).
4 •
No water can be pumped when plumbed
Be sure that the valve on the main water source supplying the DD is in the on position (not part of the
DD). Check that the lever on the bottom of the DD is pointing towards the LEFT when facing the front of the
machine.
5 •
I can pump water through the group, but the water is always cold.
Check that the PID is on (Displaying a temperature and not the word “oFF”).
… 69 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vibiemme Vibiemme Double Domobar version 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vibiemme Vibiemme Double Domobar version 3 in the language / languages: English as an attachment in your email.

The manual is 7,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vibiemme Vibiemme Double Domobar version 3

Vibiemme Vibiemme Double Domobar version 3 Additional guide - English - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info