661546
55
Zoom out
Zoom in
Previous page
1/80
Next page
Battery charger / inverter COMBI-GAMMA
090138.02 55
B2 Group (Auto Transfer Switch)
B2-01: AC IN Low Disconnect
Use constant B2-01 to determine the AC IN voltage below which level the ATS (Auto •
Transfer Switch) will switch off.
This voltage level will always lie below the • AC IN Low Connect (B2-02) level. In fact,
changing this level will also change the AC IN Low Connect (B2-02) level.
B2-02: AC IN Low Connect
This setting forms a pair with • AC IN Low Disconnect (B2-01). With this setting, one deter-
mines the AC IN low voltage at which level the ATS will switch on. This should lie above
AC IN Low Disconnect (B2-01) level to prevent continuous switching off the ATS when
the voltage is fluctuating around the level.
In fact, the parameter which is changed is the difference between • AC IN Low Disconnect
(B2-01) and AC IN Low Connect (B2-02).
The result of this is that when changing B2-01 level, this level (B2-02) also changes.•
Note: B2-02 can be ignored for a short time when AC IN Waveform Check (B2-06) is *
disabled (B2-06=0)
When the AC IN voltage drops due to the increasing charge current, the AC CHARGER •
will take care that the voltage does not drop below this level.
B2-02=B2-01+offset voltage•
B2-03: AC IN High Connect
This setting forms a pair with • AC IN High Disconnect (B2-04). With this setting, one
determines the AC IN high voltage at which level the ATS will switch on. This should lie
below the AC IN High Disconnect (B2-04) level to prevent continuous switching of the
ATS when the voltage is fluctuating around that level.
In fact, the parameter which is changed is the difference between • AC IN High Discon-
nect (B2-04) and AC IN High Connect (B2-03).
The result of this is that when changing B2-04 level, this level (B2-03) also changes.•
B2-03=B2-04–offset voltage•
B2-04: AC IN High Disconnect
Use constant B2-04 to determine the AC IN voltage above which level the ATS will switch •
off.
This voltage level will always lie above the • AC IN High Connect (B2-03) level. In fact,
changing this level will also change the AC IN High Connect (B2-03) level.
B2-05: AC IN Current Limit
Use constant B2-05 to set the specific maximum AC input current. This value is very •
important for both battery charger and inverter output load support.
When using constant B2-05, the values determine the actual AC current limit.•
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vetus COMBI1512 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vetus COMBI1512 in the language / languages: English as an attachment in your email.

The manual is 4,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vetus COMBI1512

Vetus COMBI1512 Usermanual and installation guide - Dutch - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info