815508

Vermont Castings Stardance Series Manual

9
Zoom out
Zoom in
Previous page
1/54
Next page
993-90-30007467Vermont Castings • Stardance SDDVT Installation Manual_R35 • 11/23
Vertical Termination
A vertical vent system must terminate no less than 8’ (2.44 m)
and no more than 40’ (12 m) above the appliance ue collar.
A restrictor plate (supplied) must be used, where specied,
in all vertically terminated vent systems. (Refer to Figure
2.8) NOTE: The restrictor plate supplied with the vertical
termination should be discarded. Adjust the restrictor plate
according to recommendations in Figure 2.10. A vertically
terminated vent system must also conform to the following
criteria:
• No more than three 90° elbows may be used.
• Two 45° elbows may be substituted for one 90° elbow.
No more than six 45° elbows may be used.
• Vent must rise a minimum of 2 feet (305 mm) before
o󰀨set is used.
• Termination height must conform to roof clearance as
specied in Figure 2.11.
Restrictor Plate Adjustment for Extended Pipe Runs
Adjustments can be made by loosening the adjustment screw
to allow the restrictor plate to slide up or down, Figure 2.9. A
guide for usage is shown in Figure 2.10.
NOTE: Some installations may require some adjustment by
the installer for optimum ame appearance. Optimum ame
appearance is a ame that is not subject to tall, dirty yellow
ames producing soot or ames lifting o󰀨 of the ember bed
ports.
Restrictor Plate Adjustment
• Adjust plate (Figure 2.9) to location according to
guidelines in Figure 2.10.
• Tighten attachment screw.
• Install logs following log installation instructions.
Figure 2.8 - Vertical vent termination window.
20
19
18
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
Vertical Run (in feet)
(Measure from the appliance flue collar to the top of the vent pipe.)
Horizontal Run (in feet)
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
ST132a
FDV28
Vertical
vent run
12/3/99 djt
**
Unacceptable
Venting Conguration
**No Restrictor Plate
All Vertical
Terminations in this
area Require use
of the Restrictor
Plate*
Vertical terminations
must be within this
area
Figure 2.10
FireboxRestrictorSettings
20’-27’ 28’-35’ 35’-40’
Restictor Settings 1 2 3
Note: Numbering system starts with 1 on the bottom
ST917
restrictor plate
09/22
Figure 2.9 - Loosen screw to adjust restrictor plate.
Adjustment
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermont Castings Stardance Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Stardance Series in the language / languages: English as an attachment in your email.

The manual is 7.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vermont Castings Stardance Series

Vermont Castings Stardance Series User Manual - French - 54 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info