815508
7
Zoom out
Zoom in
Previous page
1/54
Next page
773-90-30007467Vermont Castings • Stardance SDDVT Installation Manual_R35 • 11/23
Wall Centerline from Floor
Direct Vent Only
A
E󰀨ective Minimum Centerline
56" (1480 mm)
(HHT Pipe)
52” (1378 mm)
(DuraVent Pipe)
ST131b
Stardance
wall thimble
01/19
A
Figure 2.5 - Minimum wall centerline.
D. Hearth Requirements
WALL AND CEILING CLEARANCES
Direct Vent Only
A: Rear Wall 4” (102 mm)
B: Min. Clearance 45-1/4” (1154 mm)*
C: Min. Alcove Height 72” (1830 mm)*
D: Max. Alcove Depth 48” (1220 mm)
Sidewall Clearance 4” (102 mm)
*Needed for installing DuraVent Minimum Vent Kit #2792 or HHT Minimum
Vent Kit #SLP-FSSK.
A
C
D
ST101b
Stardance
Direct Vent
Min. Clrnc
01/19
B
Figure 2.6 - Dimensions and clearances to ceiling or alcove.
The Stardance Heater can be installed on any type of rigid
ooring (e.g. hardwood, ceramic tile, brick, etc). When the
heater is installed on a carpeted surface, a metal or wooden
panel extending the full width and depth of the unit must be
used as the hearth. The purpose of the hearth is to prevent
the unit from sinking into the carpet surface and reducing
the required clearance to the underside of the unit. There
are no other hearth requirements.
E.ClearancestoCombustibles
CAUTION
Hearth and Home Technologies does not recommend adhesive
based vinyl ooring due to thermal expansion. Floating-style
ooring (LVP - luxury vinyl plank or LVT luxury vinyl tile) can be
used, but it will reach temperatures up to 110 °F in a room with
ambient temperature of 70 °F. Consult ooring specications to
ensure compatibility.
HHT recommends gas stoves have 6 inches of alternative
ooring in front of the stove before using LVP/LVT regardless
if they sit ush on the oor or are elevated on a raised hearth.
For all other ooring, continue to follow clearance to combustible
requirements in the installation manual.
NOTICE: Clearances that do not meet the minimum guidelines
could result in damage or buckling to the vinyl ooring and is
done at the installer’s risk.
Figure 2.4 - Corner installation, minimum corner clearances.
ST129b
Stardance
corner specs
01/19
4" (102 mm)
4" (102 mm)
Corner Installation Minimum Clearance
Figure 2.3 - Parallel installation, minimum back and side clearances.
ST128b
Stardance
flue centerline
01/19
*4" (102 mm)
4" (102 mm)
*Measurement from rear skirt.
Parallel Installation Minimum Clearance
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermont Castings Stardance Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Stardance Series in the language / languages: English as an attachment in your email.

The manual is 7.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vermont Castings Stardance Series

Vermont Castings Stardance Series User Manual - French - 54 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info