815507

Vermont Castings Radiance Series Manual

23
Zoom out
Zoom in
Previous page
1/56
Next page
2323 3-90-30007498Vermont Castings • Radiance RADVT Installation Manual_R32 • 10/23
D. Log Set Installation
Before beginning log installation, remove stove front and
glass frame. Refer to Figures 3.24 and 3.25.
Note:Removethesafetybarrierbeforeyouremovethe
glassframe.Toremovethebarrier,simplyliftupandpull
outuntilthetabsareclearoftheircorrespondingslots
ontherebox.Thenproceedtoremovetheglassframe
byfollowingthestepsbelow.
ST139
Radiance
remove front
4/20/01 djt
Figure 3.20 - Remove the safety barrier and stove front.
ST141
pull glass latch
10/99
Figure 3.21 - Release the latches to remove the glass frame.
Before installation, inspect ember bed burner for damage.
Do not use ember bed if damaged or cracked. Small, shallow
surface cracks are acceptable.
1. Remove the logs from their packaging and inspect each
piece for damage. DO NOT INSTALL DAMAGED LOGS.
2. Install the rear log by placing it on the ember bed toward
the back of the rebox, Figure 3.22. The log should touch
the back wall of the rebox. When the log is in place, the
two (2) notches on the bottom of the log rest on the two
(2) ribs on the back side of the ember bed, Figure 3.23.
LG488
rear log
6/07
Rear Log
Figure 3.22 - Rear Log
LG487
ember bed
6/07
Ribs for Rear Log
Ember Bed
Rib Flat Spot for
Front Left Log
Rib and Flat Spot
for Front Right Log
Figure 3.23 - Ribs for Logs
3. Install the front left and right logs (Figure 3.24) by placing
them on the ribs shown in Figure 3.23. Make sure the logs
line up with the at spots on the ember bed intended for
location purposes, Figure 3.24.
4. Install the left cross log by engaging the hole on the bottom
with the pin on the left side of the rear log. Set front side of
cross log on notch in ember bed, Figure 3.25.
5. Install the right cross log by engaging the hole on the
bottom with the pin on the right side of the rear log. Set
front edge of cross log on ember bed,Figure 3.25.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from
the hot viewing glass is provided with this
appliance and must be installed.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermont Castings Radiance Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Radiance Series in the language / languages: English as an attachment in your email.

The manual is 6.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vermont Castings Radiance Series

Vermont Castings Radiance Series User Manual - French - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info