815509

Vermont Castings Intrepid - Gas Manual

14
Zoom out
Zoom in
Previous page
1/64
Next page
1414 3-90-30007474Vermont Castings • Intrepid DV-IFT Owner’s Manual_R28 • 11/23
B.AssemblingtheStove:
Tools Required
• Phillips screwdriver (stub)
• Utility knife
• Metal drill bit: size 28 (.140"/3.5mm)
• Flat-blade screwdriver
• Power drill
• Reciprocating saw
• 9/16" wrench
• 1/2” Wrench
Parts Bag Contents:
• Three (3) Vent Screws
• Two (2) Switch bracket screws
• Wood handle w/insert lifter (handle for operable door)
• Restrictor Plate
• 4" Starter pipe
• Wireless Remote
• Three (3) Phillips round-head bolts, 1/4"- 20 x 1/2"
• One (1) Tube of Vent Gasket Cement
• Four (4) CS, Hex Hd 3/8-16 x 1 Gr 2-Z
• Four (4) Washer, Fl 3/8-Z
• Owner’s Installation and Operating Manual
Unpack Stove
Using a 1/2” wrench remove the (4) lag bolts installed through
the shipping brackets and into the skid. Using a 7/16” wrench
loosen the (4) bolts where the shipping brackets meet the
base of the unit. Once loosened, tilt the unit slightly and
remove the (2) front bolts, washers and shipping brackets.
Use the (4) 1/4-20 x 1” Bolts and 1/4” washers supplied in
the manual bag to install the legs where the brackets were
once installed. Repeat previous step to install the rear legs.
WARNING
!
Only the IFT appliance is equipped with a three-prong
(grounded) plug for your protection against shock hazard
and should be plugged directly into a properly grounded
three-prong receptacle. Do not cut or remove the ground-
ing prong from this plug.
C.VentingSystemAssembly
CAUTION
!
All HHT Direct Vent Stoves have been tested and
approved to ANSI/CSA Standards and will operate safely
when installed in accordance with this instruction manual.
Read all instructions before starting installation, then follow
these instructions carefully to maximize stove performance
and safety. Report damaged parts to your dealer.
Important Safety Information
The termination cap MUST be vented directly to the outside.
The termination kit MUST NEVER be connected to a chimney
ue(s) servicing a separate solid-fuel burning appliance or
any other appliances.
• Termination cap MUST NOT be recessed into a wall,
Figure 3.1.
• The installation must conform with local codes or in the
absence of local codes, with the National Fuel Gas Code,
ANSI Z223.1 (in the United States) or with the current
installation code CSA B149 (in Canada).
• These models are approved to use HHT direct vent
pipe components, HHT termination kits and DuraVent
components. No other venting system components may
be used.
• Horizontal runs must be supported every 3 feet (914 mm)
using wall straps. Vertical runs must be supported every
8 feet (2.4 m) using wall straps. Slip wall straps loosely
on to pipe. Attach straps to framing members using nails
or screws. Tighten nut/bolt to secure pipe.
• The stove and venting system should be inspected
before initial use and at least annually by a qualied
eld service person. Inspect the external vent cap on a
regular basis to make sure that no debris is interfering
with the airow. Inspect entire venting system to ensure
proper function.
WARNING
!
Always maintain minimum clearances around vent
systems. Rear Vent Vertical Side wall: Horizontal sections
of this vent system require a minimum of 3” (76 mm)
clearances to combustibles at the top of the ue and 1”
(25 mm) clearance at the sides and bottom until the ue
penetrates the outside wall. A minimum 1” clearance all
around the ue is acceptable at this point of penetration.
FOR VERTICAL RUNS, maintain a 1” (25 mm) minimum
clearance to all sides. Do not pack the open air spaces
around the stove or ue with insulation or other materials.
Any horizontal run must have a 1/4” rise for every one (1)
foot of run towards the vent termination. Never run the
vent level or down.
WARNING
!
Failure to follow these instructions may create a possible
re hazard and will void the warranty.
WARNING
!
Any common venting of this gas appliance with other gas
appliances is not allowed.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermont Castings Intrepid - Gas at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Intrepid - Gas in the language / languages: English as an attachment in your email.

The manual is 17.23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info