815501
17
Zoom out
Zoom in
Previous page
1/30
Next page
Vermont Castings • Encore Model 2040-CAT-C Owner’s Manual_R14 • 2019 - ___ • 12/2317 8390-204C
Figure 3.3-Rotatepawland/orremoveatwashertoadjustlatch.
ST1154
door pawl
Roller
LockNut
SetScrew
ShoulderScrew
HandleStub
FlatWasher
E. Gasket Replacement (as needed)
Your Encore® Model 2040-CAT-C uses berglass rope
gasketstomakeatightsealbetweensomeparts.Withuse,
particularly on moving parts, gaskets can become brittle and
compressedandcanbegintolosetheire󰀨ectiveness.These
will need periodic replacement.
The sizes of replaceable gasket are listed below, along with
their applications.
Gasket Diameter......And the Parts it Seals
5/16” Thegriddletothestovetop(wirereinforcedgasket)
5/16” Thedampertotheupperreback
3/8” Thefrontdoorstothestovefront;andthedoorsto
each other.
3/8” Theashdoortothefrontofthebottompanel
3/16” Theouterglasspanestothedoor
Ifyouneedtochangeagasket,rstobtainanappropriate
replacementfromyourVermontCastings’AuthorizedDealer.
Waituntilthereisoutandthestovehascooled.Besureto
follow the standard safety procedure for working with dusty
materials:wearsafetygogglesandadustmask.
The procedure for replacing gaskets is the same, regardless
ofthegasketlocation.Followthesesteps:
1. Removetheexistinggasketbygraspinganendandpulling
rmly,Figure3.4.
Tighten the Damper Handle as Needed
A handle on the left side of the stove controls the damper.
The handle attaches to the damper rod with a set screw.
Periodically check the set screw and tighten as necessary.
C. Front Door Adjustment
The load doors are factory adjusted for clearance, proper
sealing and latch operation. However, the doors can
sometimes shift in transit or from use and may need to be
readjusted.Theadjustment/alignmentprocedureissimple
andonlyrequiresa7/16”wrenchandafewminutes.We
haveprovidedadetailedvideoexplaininghowtoproperly
adjust and align the doors.
D. Ash Door Adjustment
Just like the load doors, the ash door is factory adjusted for
properlyoperationandminimalsag.Ifthedoordoesrequire
adjustment to minimize sagging at the latch side, a simple
adjustmentrequiringonlya7/16”wrenchwillgetthedoor
back into proper alignment. We have provided adetailed
videoexplaininghowtoproperlyadjusttheashdoor.
Note: For video instruction please refer to www.
vermontcastings.com.ClickontheYouTubelinklocated
intheupperrighthandcornernexttothe“Search”bar.
B. Damper Adjustment (as Needed)
ThetensionontheEncore®Model2040-CAT-C’sdamperis
adjustable to compensate for compression of the gasket that
sealsthedampertotheupperreback.Toadjustthedamper:
1. Removethegriddle.Loosenthelocknutatthecenterof
thedamper,Figure3.2.
2. Turnthe pressure screw approximately one half turn
clockwise with an Allen wrench provided with your stove.
3. Tighten thelock nut. Prevent thepressurescrew from
turningasyoutightenthenut.Re-testthedamper.
Figure 3.4-Removegasketthencleanchannelwithwirebrush.
Pressure Adjusting
Screw
AllenWrench
LockNut
Damper
Figure 3.2-AdjustthedamperwiththeAllenwrench.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermont Castings Encore at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Encore in the language / languages: English as an attachment in your email.

The manual is 4.61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vermont Castings Encore

Vermont Castings Encore User Manual - French - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info