629184
58
Zoom out
Zoom in
Previous page
1/68
Next page
Verizon Wireless VZAccess Manager57
© 2004 Verizon Wireless
My communication software
shows that I am connected,
but my wireless phone does
not.
·
Depending on your device and your N
ationalAccess or
BroadbandAccess
plan, your data session may disconnect
during a dormant state. See your Calling Plan brochure for
details. Select disconnect, then connect again
·
Your call may have been disconnected due to a network
anomaly. Disconnect and try to establish your session again.
·
If you are unable to establish a session using the
NationalAccess - BroadbandAccess or the NationalAccess
connection, try the Quick 2 Net (14.4 kbps) connection. (
Note:
Quick 2 Net and Dial Up connections may be charged
differently than N
ationalAccess or BroadbandAccess
sessions. Please check your Calling Plan brochure for
details.)
I get disconnected while
using Mobile Office, or while
dialed in to my corporate
network.
·
Raise the antenna on your wireless phone, and verify that
there is a "D" on the display to indicate digital coverage. If you
are not within the digital coverage area, wait until you are back
in the Verizon Wireless digital coverage area to place your
call.
·
Check the battery strength indicator on the display of your
wireless phone. Low power may cause loss of signal.
·
Try to establish your session again.
·
Make sure the data cable between your wireless phone and
your computer is securely connected to both devices.
·
Your corporate network or Internet service provider may have
disconnected you. If the problem persists, contact your
Internet service provider or corporate network administrator for
support.
·
Check your application software setup to see if it has an
inactivity timeout. Increase the timeout to match your needs.
When I launch VZAccess
Manager:
. . . my wireless phone powers
off.
. . . the levels reported for
Battery or Signal level are
incorrect.
·
Some wireless phones do not support the commands used to
determine the battery and signal levels. If the display of the
phone differs with what is displayed in VZAccess Manager use
the information displayed on the phone.
·
You can set VZAccess Manager to display the PC's battery
level instead of the battery level of the wireless device. This
will resolve the powering off issue if it is occurring. See
WWAN Specific Settings
.
·
Also keep in mind the battery levels in VZAccess Manager
cannot update when the wireless phone is in use. The default
setting is to query the wireless phone when the program
starts, right before you establish a session and when you
disconnect. So the levels are a snapshot; they do not
constantly update. You can refresh the levels when you are
not in a session by selecting "Tools", "Refresh Signal Levels"
from VZAccess Manager's main screen.
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Verizon VZAccess Manager at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Verizon VZAccess Manager in the language / languages: English as an attachment in your email.

The manual is 1,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info