567863
18
Zoom out
Zoom in
Previous page
1/49
Next page
www.velodyne.com
12 - Digital Drive SMS-1 User’s Manual
SMS-1 SETUP – OVERVIEW
BEFORE YOU BEGIN: Once the installation has been completed, note that you can use your SMS- 1 without
performing ANY of the setup steps below. Simply use the remote to set the volume, and select the preset that
most closely matches your listening material, and enjoy! However, to reap the maximum benets of Digital Drive
technology, read on!
Special note for 230V users with video problems
For 230-volt Digital Drive SMS-1 users, the default video mode is NTSC video format. If your TV is NTSC
compatible, you will have no trouble with this mode. However, certain TVs (especially older ones) may require
PAL or SECAM video. To switch from NTSC to PAL/SECAM mode, press the DOWN ARROW four times followed
by RESET. The SMS-1 will restart in PAL/SECAM video mode. To revert back to NTSC, restore defaults by
pressing 8-9-0 on the cover screen..
Quick Setup Using Self-EQ
To perform an abbreviated setup of your Digital Drive SMS-1 using the Self-EQ function, position the microphone
in your listening position and connect it to the SMS-1 as shown in the installation instructions. Then, press 3-2-
1 on the remote. The subwoofer emits 25 “sweep tones” that are detected by the microphone and used to
automatically EQ your SMS-1 accordingly. After the sweep tones are completed, the unit automatically saves
settings and returns to normal operation. Once the self-EQ process starts, pressing the RESET button can
interrupt it.
Caution: Self-EQ resets all EQs for all presets to their default values. DO NOT use the Self-EQ feature after you
have adjusted the SMS-1 EQs manually as described below.
ON-SCREEN Setup
This section describes adjusting the onscreen settings of your SMS-1. You will be performing all the setup
functions using the buttons of your Velodyne-supplied remote control and seeing the results on your TV screen.
Words in all uppercase letters in the setup instructions (e.g., SELECT, MENU, etc.) identify the specic remote
button to be pressed or selected, or the eld on the screen you should be paying attention to. Remember to
point the remote control at the SMS-1, not your TV!
Use the UP, DOWN, RIGHT, and LEFT directional arrow buttons that surround SELECT to navigate the elds of
the setup screens. Settings are typically changed using the SELECT key, followed by the UP and DOWN arrow
keys. Alternatively, the SET +/- buttons can be used to change settings. A screen eld highlighted in reverse
video indicates your current location on the screen. Holding down the UP, DOWN, RIGHT, or LEFT arrow keys
causes the remote to repeat and you can then rapidly move through elds to arrive at the desired one. You
should be able to perform most of the setup process by using the four arrow keys and the SELECT button.
WARNING: The SMS-1 is a device that manipulates your subwoofer’s input audio signal before passing it along
to the subwoofer to play. There are tools and controls on the SMS-1 that allow you to send signals to your
subwoofer that your subwoofer may not be able to handle. Manysubwoofers contain self-protection but even
this might not be enough to handle certain conditioned signals. Use caution when setting subsonic lters, EQs,
volume levels, and other settings so that you do not send signals to your subwoofer that cause it harm. Areas of
particular concern will be highlighted throughout the setup instructions.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velodyne SMS-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velodyne SMS-1 in the language / languages: English as an attachment in your email.

The manual is 2,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info