567863
16
Zoom out
Zoom in
Previous page
1/49
Next page
www.velodyne.com
10 - Digital Drive SMS-1 User’s Manual
4. Connect the audio/video cables between your SMS-1 (EQ OUTPUT VIDEO/LEFT/RIGHT yellow, white,
and red respectively) and your electronics (receiver, processor, TV, etc.). Insert the color-coded cable
plugs into the correct EQ OUTPUT receptacle – the yellow plug into the VIDEO jack, the white plug
into the LEFT jack, and the red plug into the RIGHT jack. The opposite ends of the cables should
be connected to your receiver/processor. The yellow VIDEO cable goes to an available composite
video input (e.g. aux), and the white/red AUDIO (L&R) cables go to a corresponding audio input. As an
alternative to composite video, you may want to use S-video (S-video connector not included). Connect
the S-video from the SMS-1 to an S-video compatible input on either your processor or TV. Consult your
receiver/processor and/or TV owner’s manual for more information.
5. Connect your subwoofer(s) to the SMS-1 using the XLR connector or LFE out RCA connector.
6. Defeat the crossover on your subwoofer(s) (if possible) and set its volume to the middle setting.
NOTE: Make sure the audio output goes into your AUDIO system, not your TV! The SMS-1 will generate test
tones used to match the SMS-1 to your satellites and to correct for room anomalies that need to be played by
your main audio system.
7. Insert the XLR microphone cable’s 3-pin male plug into the MIC INPUT jack (location 7 on Figure 2) on
the front or back panel of the SMS-1.
8. Slide the microphone (male connector end rst) down through the open, circular sleeve of the tabletop
microphone stand. Position this assembly at a desired listening position.
NOTE: The Digital Drive Accessory Kit includes a microphone stand adapter (1/2”-27 thread) for use with
professional mounting stands. Be sure to rst remove the inner thread piece (3/8”-16) before using.
9. Connect the XLR microphone cable’s female jack end with the male connector end of the microphone.
10. Sheath the microphone pickup with the foam windscreen cover as a protection against dirt and airborne
contaminants.
A Word About Interconnect Cables
When installing your new Velodyne SMS-1 using the line level connections, you should always use shielded
phono cables. There are many quality cables available today, most any of which will work perfectly well. We
do recommend that you keep the length of cable as short as possible to avoid any potential noise problems..
A Word About Connecting More Than One Subwoofer
Note that your SMS-1 can control up to three subwoofers. Each of the three subwoofers will receive the same
conditioned signal from the SMS-1. If you wish to run more then three subwoofers, or wish to individually
customize the signal to dierent subwoofers, you will need more than one SMS-1 connected in a “daisy-chain”
conguration. This section describes setup in a daisy-chain conguration.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velodyne SMS-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velodyne SMS-1 in the language / languages: English as an attachment in your email.

The manual is 2,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info