567716
8
Zoom out
Zoom in
Previous page
1/20
Next page
www.velodyne.com
2 - Impact Series User’s Manual
Placement
The rst step in installing your new Impact sub is to determine where it will be placed in the room. Unpack the
system carefully and use the following guidelines in order to nd the best room placement option.
True subwoofers operate at extremely low frequencies which are primarily omni-directional. Keep in mind that
frequency response and output level can be drastically inuenced by placement, depending on the acoustic
properties of the listening room. To obtain optimum output from your subwoofer, try placing it within a foot of a
corner. This location will oer the greatest output levels and optimum low frequency extension. If at all possible,
your subwoofer should be placed along a wall. The worst location for a subwoofer is typically far away from any
walls and close to the center of your room. Avoid these locations when possible. When using a pair of Velodyne
subwoofers in 2-channel stereo, it is preferable to feed each subwoofer with one channel and place each
subwoofer near the satellite of the same channel.
Depending on the size and type of furnishings in the room, perfect placement may not be possible. Finding the
best location within your environment will likely require some experimentation. We suggest you experiment with
the location during setup to nd what sounds best to you when seated in your typical listening position.
Regardless of where you install your Velodyne subwoofer, it must remain in an upright position. Using, shipping
or storing the subwoofer in any other position for an extended period of time may result in damage to the unit
not covered by warranty.
Caution!
This subwoofer has electronics built into the cabinet. Do not place the cabinet next to sources of heat such as
furnace registers, radiators, etc. Do not place the unit near sources of excessive moisture, such as evaporative
coolers, humidiers, etc. The power cord should be routed in such a way that it will not be walked on, pinched
or compressed in any way that could result in damaging the insulation or wire.
Your Velodyne Impact subwoofer is NOT magnetically shielded. Should you nd it necessary to use it with an
older CRT monitor or TV, keep it at least two feet from the monitor. Experiment for correct distance by minimizing
distortion of the picture and colors.
INSTALLATION
Inputs
Your new subwoofer is equipped with speaker-level and line-level inputs. Use the LINE LEVEL jacks when
connecting your subwoofer to a pre-amp, signal processor (such as LFE out), linelevel crossover, or receiver
with pre-amp level outputs. When using the line level jacks, some receivers may not provide enough signal to
have the unit’s auto-on feature operate properly. Additionally, this lack of signal may also cause the subwoofer
to produce less output than it is capable of.to produce less output than it is capable of.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velodyne Impact-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velodyne Impact-10 in the language / languages: English as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info