567716
9
Zoom out
Zoom in
Previous page
1/20
Next page
www.velodyne.com
Impaact Series User’s Manual - 3
To alleviate this condition, we recommend the following steps:
1) If using line level jacks, BOTH THE LEFT AND RIGHT INPUT CAN BE USED – never use just the left or
just the right input. If the subwoofer’s signal comes from the LFE channel of your receiver, use a “Y”
splitter to connect to both the left and right inputs.* If using line level connections from a preamp or
signal processor, use both Left and Right inputs from your preprocessor or preamp and connect them
to the Left and Right inputs on your subwoofer. (See gure 2a on page 7.)
* This dual male-to-female “Y” splitter can be found at your local electronics store.
2) If using a receiver with LFE out, be sure the LFE channel is sending adequate signal to the subwoofer.
We recommend setting the subwoofer’s level to the 9 o’clock position (the 1/4 volume setting) and then
adjust the LFE channel on your receiver or processor to achieve the desired bass output. See your
receiver or processor’s owner’s manual for more information. (See gure 2b on page 8.)
The SPEAKER LEVEL jacks connect directly to the speaker outputs of any amplier, integrated amplier, or
receiver. Your amplier section will notice no additional loading eects when you use these inputs due to their
very high impedance. If using the SPEAKER LEVEL inputs, you DO want to connect both channels, since
dierent bass information might be present in each channel going to your main speakers.
Important!!!
Do not use both LINE LEVEL and SPEAKER LEVEL connections simultaneously!
Caution!!!
To avoid damage to your main amplier, be sure to maintain correct polarity when making all connections - red
(positive) to red, and black (negative) to black. Be sure all connections are tight, and that there are no loose
strands or frayed wires.
Volume Control
This control allows you to balance the output from the subwoofer to the main speakers in your system. This
control should be set to achieve similar output levels from both the main speakers and subwoofer when listening
to music. A good starting point for the volume control is two or three graduations from minimum.
Warning:
Some manufacturers preset their receivers with the Sub-Out channel signal at a minimum level. It is very important
to verify that your receiver Sub-Out channel is set to the same output level as your front right and left channels.
Refer to your receiver manual for the individual channel level adjustment procedure. If your receiver Sub-Out
channel is set too low, the subwoofer may appear to have a weak output, it may sound noisy or distorted, and
the Auto On/Off feature may not operate properly.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velodyne Impact-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velodyne Impact-10 in the language / languages: English as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info