622070

Velleman WS1060 Manual

10
Zoom out
Zoom in
Previous page
1/77
Next page
WS1060
V. 02 – 26/04/2013 10 ©Velleman nv
4. Press + repeatedly to display the minimum values for: outdoor humidity, outdoor temperature, wind chill
temperature, dew point, indoor humidity, indoor temperature.
5. Press HISTORY to return to normal mode.
Resetting a minimum or maximum
To reset a minimum or maximum:
1. Enter minimum or maximum reading mode and press + to display the value that you want to reset.
2. Press and hold SET for 3 seconds.
3. Repeat for any other minimum or maximum value that you want to reset.
4. Press HISTORY to return to normal mode.
8. Resetting
To reset the weather station to the factory defaults, press and hold the + key for 20 seconds.
9. Troubleshooting
Problem
Possible Cause
Solution
Transmission problem
Distance between the two units is too long
Reduce distance
Shielding materials between two units
(thick wall, steel…)
Find a different mounting location
Interference from other sources
Eliminate interference sources
Data on LCD is
illegible
No data reception
Find a different mounting location
Low batteries
Replace batteries
Incorrect data
Low batteries
Replace batteries
Incorrect settings
Reprogram the weather station
10. Calibration
For accurate measurements, you can calibrate wind speed, temperature, humidity, and rainfall measurements
using calibration tools (not incl.).
To enter calibration mode, proceed as follows:
1. From normal mode, press and hold HISTORY for 8 seconds.
The station is now in calibration mode. The wind factor digits on the display flash.
2. Press SET to go to the next setting; use the + or MIN/MAX keys to change the values.
3. To exit the calibration mode, press HISTORY.
See below for a description of each calibration setting.
Wind speed calibration
The default wind speed calibration setting is 1.0. The adjustment factor ranges from 0.75 to 1.25. You can set it
in 0.01 increments.
Wind speed is the most sensitive to installation constraints. The following factors influence wind speed
measurement:
the location of the weather station: proximity of buildings, trees, or other obstructions
the wear of the moving parts of the anemometer.
To calibrate the wind speed, we recommend using a calibrated wind meter (not incl.) and a constant-speed,
high-speed fan (not incl.).
Temperature calibration
You can calibrate indoor and outdoor temperature measurements.
The following factors influence temperature measurement:
proximity of heat sources, such as buildings, the ground…
installation in direct sunlight without proper shielding in hot weather environments.
To calibrate the temperature, we recommend using a mercury or alcohol thermometer (not incl.). Do not use
bi-metal (dial) or other digital thermometers, as they have their own error margin. Do not use a local weather
station in your area (difference in location, timing of updates, and possible calibration errors).
To calibrate the temperature, proceed as follows:
1. Place the temperature sensor in a shaded, controlled environment.
2. Place the thermometer right next to it.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velleman WS1060 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velleman WS1060 in the language / languages: English, German, Dutch, French, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 2,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info