585216

Velleman HAM982K Manual

6
Zoom out
Zoom in
Previous page
1/52
Next page
HAM982K 6 VELLEMAN
7. Factory Settings
These are the factory settings – they can be modified if they are not applicable for your situation. Refer to the next
chapter ("8. Programming the Panel") for details on how to modify the settings.
The factory settings allow for the system to be operated as a local alarm panel without programming except for the
master and user codes.
LOCATION PARAMETERS DEFAULT PRESETS PROGRAM DATA
01 master code 1234 code=1234
11-18 user code 1-8 nil nil
21 zone 1 multiple trigger, entry delay 1, 500ms response code1=1, code2=1, code3=2
22 zone 2 multiple trigger, entry delay 1, 500ms response code1=1, code2=1, code3=2
23 zone 3 multiple trigger, instant, 500ms response code1=1, code2=0, code3=2
24 zone 4 multiple trigger, instant, 500ms response code1=1, code2=0, code3=2
25 zone 5 multiple trigger, instant, 500ms response code1=1, code2=0, code3=2
26 zone 6 multiple trigger, instant, 500ms response code1=1, code2=0, code3=2
27 zone 7 multiple trigger, 24hr instant, 500ms response code1=1, code2=3, code3=2
28 zone 8 multiple trigger, 24hr instant, 500ms response code1=1, code2=3, code3=2
30 exit delay exit beep enabled, 60 seconds code=1, duration=60
31 entry delay 1 entry beep enabled, 30 seconds code=1, duration=30
32 entry delay 2 entry beep enabled, 60 seconds code=1, duration=60
33 siren duration arm-disarm ring-back disabled, 300 seconds code=0, duration=300
40 arming type forced to arm code=0
41 alarm handover disabled code=0
HOME isolation zones in memory nil nil
85 power up delay disabled code=0
86 periodic battery test disabled code=0
8. Programming the Panel
BEWARE: to avoid triggering by the tamper switch, make sure the cabinet is firmly closed before applying power to
the system. Also, do not install a battery after power-on but before a user code is programmed: the tamper switch will
trigger the alarm instantly, but there is no user code to turn it off and the master code cannot be used for disarming.
The panel can be programmed from the system keypad. Enter programming mode, then key in the 2-digit
Programming Location or address, followed immediately by the desired programming values (program data), then
press the '#' key to store the data. The system will either confirm storage with 2 beeps, or signal an unsuccessful
storage attempt with 5 beeps. If you are not sure of the values that have been entered, program the programming
location again. When programming is finished, press the '' key twice to exit the programming mode.
a. Enter Programming mode
To enter the programming mode, enter either the factory set master code (1234) or your own master code (when
set), then press the '' key twice to confirm your entry. The console will beep twice to confirm that the system is in
programming mode – the PROGRAM LED will light up.
If the factory set master code was replaced and the new master code is lost, use the DAP jumper to override the
entry code and enter the programming mode directly. The DAP jumper is located on the master circuit board. Follow
this procedure precisely to use the DAP jumper:
1) Disconnect the power supply including both AC power and the backup battery.
2) Set the jumper from the OFF to the ON position.
3) Reconnect the power supply, the console will beep continuously.
4) Put the DAP jumper back to OFF ; the beeping stops and the PROGRAM LED is on.
5) The system is now in programming mode and ready to receive new data.
6) The DAP jumper should be left in the OFF position after programming.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velleman HAM982K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velleman HAM982K in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info