585216
2
Zoom out
Zoom in
Previous page
1/52
Next page
HAM982K 2 VELLEMAN
1M 2M 3M 4M 5M 6M 7M 8M 9M 10M 11M 12M
0
1M
2M
3M
4M
5M
6M
7M
8M
1M
2M
3M
4M
5M
6M
7M
42.1
-42.1
3. PIR Detector
a. Technical Specifications
Detection element low noise dual element pyro sensor
Operating voltage 8-16Vdc ; 12Vdc nominal
Current consumption typical 15mA at 12Vdc
Power-up delay typical 2 minutes with flashing LED indication
Alarm period 2-3s
Alarm output N.C. relay contact with 10 in-line resistor. Contact rating: 28Vdc, 0.1A
Walk test with LED alarm indicator
Pulse counting Normal response or 2 pulses within 12 seconds for "harsh" environments
Tamper switch N.C. contact with 10 in-line resistor. Contact rating: 12Vdc, 50mA
Operating temperature -10 to +55°C
Humidity max 95% non-condensing
EMC conform to CE standard
Dimensions (HxWxD) 116 x 73.5 x 74mm
b. PCB layout
1. Pyro-sensor (do not touch this sensor!)
2. Walk test & alarm indicator
3. Tamper switch
4. Pulse count jumper ("harsh": for environment with high risk of false detection)
5. LED on/off jumper (on = flashing during start-up, on during operation)
6. Connection terminal block:
Tamper: if a tamper switch is required, connect these terminals to a 24h
normally closed (NC) zone in the alarm control panel. Opening the
housing will trigger a tamper signal.
12Vdc: connect (+) to an 8-16V power source, usually from the alarm control
panel. Connect (-) to the common grounding point.
Alarm: the alarm output relay of the detector. Connect these terminals to a
normally closed (NC) zone in the alarm control panel.
c. Installation
Install the detector indoors, on a stable surface with a clear view on the protection area.
Avoid mounting where hot or cold air may blow directly onto the device and where objects
in the detection field may change temperature rapidly (heating or air-conditioning devices).
Considering the detection angle of the device (see figure on the right), corner mounting is
recommended, at a height of 2 to 3 meters.
Procedure:
1. Open the cover by inserting a small screw driver into the edge of the unit and turning it to release the cover.
2. Remove the PCB by releasing the two fixing screws from the support post - DO NOT DROP THE PCB!
3. Numerous "knockouts" are provided on the back plate. Punch the one which will provide the best cable entry.
4. The two fixing holes on the back of the back plate are for surface mounting. The two fixing holes on the left and
right of the back plate are for corner mounting. Fix the back plate firmly on the wall with the two enclosed screws.
5. Put the PCB back onto the back plate and fix it firmly. Connect the wires to the terminal block.
6. Clip the front cover back in place on the back plate. See to it that the tamper switch is depressed when the front
cover is in place.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velleman HAM982K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velleman HAM982K in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info