162090
27
Zoom out
Zoom in
Previous page
1/30
Next page
Digital (standard):
Route the black/white A1 cable of the
wiring harness to the speedometer signal
pick-up point. Refer to the vehicle-specific
data sheets for location and connection
details (available on CD-ROM).
Digital speedometer signal requirements:
Frequency: 0 Hz - 4 kHz square-wave
signal (no inductive sensor)
Low - level:<1V
High - level:4V-24V
Analogue (for retrofitted speedometer
senders and magnetic sensors):
Connect the short black/white A3 cable
(directly at ISO chamber A connector) of
the wiring harness to the output of the
speedometer sensor or the magnetic
sensor.
Operation without speedometer
signal
Operation of the navigation system is possible
without a speedometer signal. However, in
the absence of a speedometer signal the fol-
lowing functional restrictions may arise:
Inaccurate navigation
Inaccurate or invalid information in trip
computer
Limitations with regard to SDVC (speed-
dependent volume control)
Other signals (ISO chamber A):
Connect the white/yellow wire (A2) to a
suitable point of the reversing signal
lead (positive lead of reversing lamp).
Connect the grey wire (A6) to a suitable
point of the low beam (not to the dash
panel illumination!).
Connection to the dash panel illumina-
tion may result in malfunctions of the
navigation system (e.g. extremely slow
reactions to operating steps and system
crashes.).
Connecting system components
(ISO chamber B)
Active remote control holder
RCD 5400 (accessory):
Connect the remote control cable plug
to the mini-DIN socket on the signal
cable.
Loudspeaker (accessory):
If required, connect separate loudspeaker
to signal cable (B5 and B6). The loud-
speaker impedance should be between
4 and 8 Ohm.
Loudspeaker mute/MUTE (option):
Connect the brown/white wire (B4) of
the signal cable to the MUTE input of
the car radio.
Playback of voice messages via the
vehicle loudspeaker
For playback of the acoustic guidance in-
structions via the front left vehicle loud-
speaker, an MA 1300 adapter cable (acces-
sory) can be connected between the loud-
speaker lead and the audio output of the
navigation computer.
Connect the brown/white wire (B4) of
the signal cable to the MUTE input of
the adapter cable.
29
OPERATION SETUP INSTALLATIONCONTENTS
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for VDO Dayton pc 5200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of VDO Dayton pc 5200 in the language / languages: English as an attachment in your email.

The manual is 3,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info