813305

Varde Shape - Smoke Control Kit Manual

2
Zoom out
Zoom in
Previous page
1/8
Next page
2
1. General
These instructions apply to the Shape product listed
when fitted with a Smoke Control kit.
Appliance Smoke control kit Part No.
Shape VD-SHAPESZKIT
NOTE: These appliances have been independently tested
to PD6434 and have been exempt from the controls that
generally apply in smoke control areas hence are
considered suitable for use in Smoke Control Area when
burning wood and ONLY when fitted with the relevant
Smoke Control kit detailed below.
To meet the Smoke Control requirement this appliance
must be operated correctly in order to minimise the
amount of smoke produced.
Burn dry wood only.
These instructions must be left with the user and
kept with the original instructions which they now
supersede.
2. Recommended Fuels
Wood Logs:
Burn only seasoned timber with a moisture content of
less than 20%. To ensure this, allow cut wood to dry for
12 to 18 months.
Poor quality timber:
• Causes low combustion efficiency.
• Produces harmful condensation.
• Reduces effectiveness of the air control and life of
the appliance.
Do not burn construction timber, painted, impregnated /
treated wood, manufactured board products or pallet
wood.
3. Lighting
Top-down lighting
Theuseof‘top-down’lightingisrecommended,where
you light the wood at the top of the combustion chamber
instead of the bottom.
Place four small logs in a cross on the bottom plate of the
combustion chamber with a small distance between each
log.
Place 8 - 12 smaller sticks in a cross on top of the logs.
Place 2 - 3 firelighters at the top and in between the sticks.
A thin layer of ashes at the bottom of the appliance
makes lighting a fire easier.
Recommended Log Quantities
Length 20-25 cm
Diameter (max) 10 cm
Quantity (3-4 logs) 1.8 kg
Before lighting the appliance, open the shaking grate by
pulling the lever all the way out. Open the valve on the
ash-pan for ignition air and open the valve on top rear of
the appliance for combustion air (alternatively, leave the
ash-pan open slightly for a short period, if there is no
wind and no draught in the chimney), this allows the fire
to catch.
Always remember to close the ash-pan after lighting the
fire or overheating can occur, which is not covered by the
warranty.
Light the paper or firelighters.
Close the door.
Once the fire is burning, close the ignition air control on
the ash-pan (The handle is in the vertical position). When
the appliance is at nominal temperature air should not be
added through this control, or overheating can occur
which is not covered by the warranty.
Allow the fire to become established until there is a
glowing bed of charcoal. You can then add fuel and adjust
the appliance, see the notes on refuelling.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varde Shape - Smoke Control Kit at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varde Shape - Smoke Control Kit in the language / languages: English as an attachment in your email.

The manual is 0.87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info