550348
11
Zoom out
Zoom in
Previous page
1/24
Next page
11
2 Attention messages and alarms
III UWATEC
®
Aladin
®
ONE
Aladin
®
ONE draws the diver’s attention to certain situations and warns the diver of unsafe diving practices.
Attention messages and alarms are visual only.
III
English
2.1 Attention messages
Attention messages are communicated to the
diver visually by symbols, letters or flashing fig
-
ures.
Attention messages come up in the following
situations (more information can be found on the
listed pages):
Page
Maximum Operating Depth / max. ppO
2
is reached 15
Oxygen toxicity reaches 75% 15
No-stop time less than 3 minutes 16
Low battery warning 8
2.2 Alarms
Alarms are given to the diver visually by flashing
symbols, letters or figures.
An alarm occurs in the following situations (more
information can be found on the listed pages):
Page
Oxygen toxicity reaches 100% 15
Ignored decompression 17
• Exceeding the prescribed ascent rate
14
• Low battery alarm 8
WARNING
Serious injury or death may result from failing to immediately respond to
alarms given by Aladin
®
ONE.
3 Preparation for the dive
Aladin
®
ONE is set to 21% oxygen (air) from the factory. If you wish to change this or any other setting, you
need to do so using the SmartTRAK software and the infrared interface. Chapter III describes the most
common
settings. On the next page you will find an overview with all possible Aladin
®
ONE
settings and page
references.
3.1 Setting the gas mixture
Before every dive and after changing the tank, make sure that the settings
for the gas mixture correspond with the current mixture used. An incorrect
setting causes Aladin
®
ONE to miscalculate this particular dive. If the fraction
of oxygen is set too low this can lead to oxygen poisoning without warning.
If the value is set too high decompression sickness may occur. Inaccuracies in
the calculations are carried over to repetitive dives.
The setting of the gas mixture can be changed only via SmartTRAK.
After changing the gas mixture with SmartTRAK you have to click
in the top row
on
the
"write" icon, otherwise the setting will not be written to the Aladin
®
ONE.
The time to reset the O
2
% mix to air can be set with SmartTRAK between 1
and 48 hours or to "no reset" (default).
WARNING
"Write"
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for UWATEC Aladin One at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of UWATEC Aladin One in the language / languages: English as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of UWATEC Aladin One

UWATEC Aladin One User Manual - German - 24 pages

UWATEC Aladin One User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info