741489

Urmet 1067-026 Manual

5
Zoom out
Zoom in
Previous page
1/12
Next page
DS1067-058 5
ENGLISH
GENERAL DESCRIPTION
Keypad with tempered glass front side, “soft-touch” technology and OLED display.
This allows to control and program the 1067 series systems, is equipped with a proximity key reader
1067/332, 1 programmable auxiliary entries and one microphone for environment listening (by phone with
PSTN or GSM interface). Furthermore, it is provided with a vicinity sensor that allows the activation of full
functionality of the device that is typically in a state of low consumption; placing the hand near the area
above the logo switches on the backlight, the display shows the predefined information and the key reader
becomes active. After 30 seconds from the last action, the keypad returns to standby mode.
Besides the usual alphanumeric and navigation keys, there are 4 additional keys available whose
functions, when activated, are visible by means of an icon on the above display area.
POSITIONING
Keypad must be positioned:
in an environment that is sheltered and protected from water and
humidity;
on a dry and level wall;
in the proximity of the accesses to area to be protected;
in an inner location which is not subjected to excessive sudden
rises/falls in temperature, and is protected by anti-burglar system;
at 160 cm height for normal installations, or at 120 cm height for
installations suitable to disabled users.
WIRING
Keypad can be connected on bus either in a cascade or star. Keypad position along bus is not important.
The overall length of all bus sections must not exceed 400 metres. For wiring, use 4 lead screened cable
(2 leads for power supply and 2 leads for data connection). Lead section must be chosen taking into
account voltage drop caused by connection length.
In counting out overall system absorption, also consider max consumption in keypad (110 mA).
INSTALLATION
The 1067/026 keypad can be installed either on a wall or above a round, flush mounting box or 3-seated
built-in case. To install the keypad proceed as follows:
Remove the keypad from the wall bracket by sliding it (Fig.1).
Secure the support bracket to the wall with 6 mm plugs (provided), or on the built-in case if available,
keeping the terminal strip downwards (Fig.2) using the mountings “A’ or “B”. Avoid over-tightening the
screws, in that they may cause the bracket to curve, making it difficult to assemble the keypad onto the
bracket itself
For the anti-removal, use two plugs supplied at the holes "C" and fix also block "D".
Connect the cable to the terminal board “E”.
Insert the cable that comes out of the keypad into the dedicated connector
“F”. Place the cable so that
it fits into the specially designed space at the bottom of the keypad; this prevents it from being crimped
when assembling the keypad to the bracket.
Insert the keypad block in the bracket and slide it downwards.
Secure with locking screws “G” (Fig.3).
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Urmet 1067-026 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Urmet 1067-026 in the language / languages: English, German, Italian as an attachment in your email.

The manual is 0,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info