636392

Unox XF180 Classic Manual

6
Zoom out
Zoom in
Previous page
1/72
Next page
UNO
X
R
II. INSTRUCTIONS FOR
THE USER
The appliance cannot be cleaned with a jet of
water.
Never wash the cavity with acids or aggressive
detergents. Use only water and soap.
The appliance is made for a specific professional
use and must be used by qualified personnel only.
1. INSTRUCTIONS FOR THE OPERATOR
WARNING:
carefully read this user manual before starting to
operate with the appliance as it gives you important
information regarding safety during installation, use
and maintenance of the appliance itself.
Keep the manual in a safe place where the different
operators that work with the appliance can easily
find and read it.
For any eventual repair, please apply only to
authorized service centres. Always require original
UNOX spare parts.
Failure to observe the above suggestions can
compromise safety of the appliance and the
guarantee will not be recognized anymore.
2. NOTES FOR USE
Premise:
This appliance must be used only in the way in which
it was expressly intended. The ovens were designed
to cook food as here below described. Every other
use is to be considered improper.
The oven allows you to work on temperature
between 0 and 260° C. It can be used to:
- bake all types of bread and pastry, both
fresh and frozen;
- cook all gastronomy preparations, fresh or
frozen;
- regeneration of refrigerated or frozen food;
- cook meat, fish and all kind of vegetables.
When placing the food in the cooking chamber,
leave at least 20 mm between the trays in order to
allow the hot air to circulate inside the cavity.
Please avoid to put salt on the food inside the
cavity.
3. CONTROL PANEL
In base al tipo di forno utilizzato può essere
presente uno dei seguenti pannelli comandi:
pannello comandi Classice pannello comandi
Dynamic.
OVENS MODEL
CONTROL PANEL
TYPE
XF100-TG
Classic
XF100-GR
Classic
XF110-TG
Classic
XF110-GR
Classic
XF130-TG
Classic
XF130-GR
Classic
XF135-TG
Dynamic
XF138-TG
Dynamic
XF180
Classic
XF185
Dynamic
XF188
Dynamic
XF190
Classic
XF195
Dynamic
XF103
Manual
XF113
Manual
XF133
Manual
XF183
Manual
XF193
Manual
3.1 DESCRIPTION AND USE OF Classic
CONTROL PANEL
The control panel can work both in the manual and
in the programmed mode.
For each cooking cycle (both in the manual and
in the programmed mode) the operator can set
cooking time and temperature.
MANUAL MODE
Switching On / Switching Off
As soon as current reaches the appliance, the
control panel switches automatically on; on the
display you will read the digits 0.00 (they express
the time in hours.minutes), the LED of the “TIME”
switches on as well as the lights inside the cavity.
15 minutes after the end of the cooking cycle (both
in the manual and in the programmed mode) both
in the cases that a program finishes or the operator
pushes the START/STOP key, if no keys are pressed,
the control panel switches automatically off. The
lights, all the display and all the LEDS will be
switched off, except for the START / STOP LED. To
switch on the control panel it is sufficient to press the
START/STOP key.
SELECT key.
The SELECT key allows the operator to select two
ENGLISH
ENGLISH
6
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Unox XF180 Classic at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Unox XF180 Classic in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info