636392

Unox XF180 Classic Manual

7
Zoom out
Zoom in
Previous page
1/72
Next page
UNO
X
R
parameters: TIME and TEMPERATURE.
TIME set up
To set the time of functioning, it is sufficient to
operate on the + and – keys (time can be set from 0
hours and 01 minute to 9 hours and 59 minutes)
When you read INF on the TIME display, the oven
will work continuously until you stop it pressing the
START/STOP key.
TEMPERATURE set up
To set the temperature desired inside the cavity
it is sufficient to operate on the + and – keys
(temperature can be set from 0 to 260°C – starting
temperature 30°C)
Start / Stop cooking cycle
It is possibile to start the cooking cycle pressing the
START / STOP key (the related LED will switch on).
It is possibile to stop the cooking cycle pressing the
START / STOP key.
At the end of a cooking cycle the heating elements
and motors will be switched off, the buzzer will ring
for 15 seconds, the digits 0.00 will flash for 45
seconds on the display, the set temperature remains
the one entered at the beginning of the cooking
cycle and the START/STOP LED will remain turned
on.
If during the 45 seconds of flashing digits (0.00) the
operator set a time (using the + or – keys), the oven
automatically starts functioning.
At the end of the 45 seconds or if the cooking cycle
is interrupted by pressing the START / STOP keys,
all the parameters previously set will turn into 0 (the
operator will be in the same situation there is when
the oven has just been turned on) and the START/
STOP LED will be switched off.
Visualization and modification of the
cooking parameters during the functioning
of the oven
While the oven is working, it is possibile to visualize
the parameters and modify them if the oven is
working in the manual mode; to scroll the different
parameters (time, temperature) you have to push
the SELECT key.
If you select time, the display visualizes the remaining
time (COUNTDOWN related to the selected step).
If you select temperature, the display alternately
visualizes for 4 seconds the set tempeture (fixed LED
– it is possibile to modify the temperature using +
or – keys) and the measured temperature (flashing
LED).
PROGRAMMED MODE
There are 70 programs available.
Memorization of a new program
To memorize a cooking program it is necessary to
proceed as follows:
- enter the programming mode pushing the P
key: on the display you will read the writing
P01
- select the number of program you desire by
using the + or - keys (the program number
will show on the display)
- press the SELECT key
- set the cooking parameters as explained in
the manual mode
- save the program by pressing the MEM key
for 5 seconds; the storage of the program
will be confirmed by the sound of the buzzer
and by the visualization of the chosen
program number on the display
- press the P key to go back to the manual
mode.
Recall of a memorized program
To recall a memorized program it is necessary to
proceed as follows:
- enter the programming mode pushing the P
key: on the display you will read the writing
P01
- select the number of program you desire by
ENGLISH
ENGLISH
7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Unox XF180 Classic at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Unox XF180 Classic in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info