806607

United office ULG 300 A1 - IAN 273398 Manual

9
Zoom out
Zoom in
Previous page
1/53
Next page
- 6 -
Preparing for cold lamination
If you have previously performed hot
lamination:
After hot laminating, allow the laminator
to cool down completely before beginning
with cold lamination. Remember, the rollers
inside the laminator will still be hot. These
can damage the laminating pouch and the
document to be laminated!
³Insert the foil guide rails qin the designated
holes on the rear of the laminator.
³Pull out the document supports sso that the
documents can be pulled in straight into the
slot for manual foil feed t.
³Insert the plug of the laminator into a mains
power socket.
³Provide a firm location for the appliance.
³Set the selector switch for hot and cold lamina-
tion ito "COLD".
Take note: For cold lamination, ALWAYS place
the foil thickness switch oat 125 microns. The
red ON/OFF indicator lamp uand the
green indicator lamp "Ready" y now
glow.
³Place the document to be laminated into a
laminating pouch of the matching size.
Make certain that all corners of the docu-
ment have at least two millimetres of space
to the edge of the laminating pouch, as
shown in Fig. 1.
Make certain that you use only one pouch
for laminating. First open it up, as shown
in Fig. 2.
For further information about the lamina-
tion process, please read the section
"Lamination process".
Lamination process
³Lay the laminating pouch onto the foil guide
rails q. Lay the right or left edge of the lamina-
ting pouch against the foil format restraint r
(closed side leading). Slide the foil format res-
traint rtogether until the selected format size
is reached. This prevents the laminating pouch
from being pulled in at an angle.
Should the laminating pouch be pulled in
at an angle, use the anti-blocking function
as described in the chapter "Anti-Blocking
Switch (ABS)".
³Now slide the laminating pouch slowly into the
slot for manual foil feed t.
³When you have slid the laminating pouch seve-
ral centimetres into slot for manual foil feed t,
it will start to be pulled in automatically.
Release the laminating pouch as soon as you
notice it being pulled in automatically.
Ensure there is at least 45 cm of open space
in front of the laminator. If you do not, the
laminating pouch will not be completely
ejected from the laminator after lamination.
This could damage the laminated pouch.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for United office ULG 300 A1 - IAN 273398 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of United office ULG 300 A1 - IAN 273398 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 0.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info