Manual Unical EVE 05 CTFS 24 (page 29 of 36) (English)

652336

Zoom out

Zoom in

1/36

Adjustment info

°C

Outlet pressure test nipple

fig. 27

2.6 - ADJUSTING THE

BURNER

All the instructions below are for the exclusive

use of qualified technicians.

All the boilers leave the factory calibrated and

tested.

If it is necessary to change the calibration fol-

lowing changes in the type of gas or adapta-

tion to the supply network conditions, it is

necessary to recalibrate the gas valve.

WARNING: During these steps do not draw

Domestic Hot Water.

For that reason it is necessary to know the

boiler operation in chimney-sweeper mode.

In order to activate this function, push and

keep depresses the reset push button for

3 seconds, on the control panel, then push

once again the same button: the display

symbols “F” and “L” will be lighted (F: blink-

ing – L: fixed) and the boiler will operate at

the maximum capacity. By pushing again

the reset push button: the display symbols

“F” and “L” will be lighted (F: blinking – L:

blinking) and the boiler will operate at the

minimum capacity. The chimney sweeper

function remains active for 15 minutes. For

cleaning this function before this fixed

period, switch OFF and ON the boiler.

To correctly regulate the gas valve, follow the

steps below:

1) Maximum output adjustment

- check the value of the supply pressure (see

table NOZZLES - PRESSURES);

- Remove the cover (A) protecting the pres-

sure regulator on the top of the modulat-

ing coil.

Connect a manometer at the outlet gas

pressure test nipple (fig. 28).

Activate the chimney sweeper function to

the maximum capacity (“F” blinking; “L”

fixed); when the burner is ignited, check

that the “MAXIMUM” pressure value cor-

responds to that indicated on the table

“NOZZLES - PRESSURES”:

- Correct eventually the value rotating the

nut “C” with a 10 mm wrench (fig. 28);

by rotating clockwise, the gas pressure

increases, anticlockwise the gas pressure

is reduced.

2) Minimum output adjustment

- Push a second time the reset push button

and the boiler will operate at the minimum

capacity (both leds F and L will blink).

- When the burner is ignited, check that the

MINIMUM pressure value corresponds to

that indicated on the table “NOZZLES –

PRESSURES, etc.

- Correct, eventually, the value rotating the

red screw “B” with a cross-screw driver or

a 6 mm wrench (fig. 28): by rotating

clockwise the gas pressure increases,

by rotating counter clockwise the gas pres-

sure decreases

GAS VALVE

CHIMNEYSWEEPER

ACTIVATION

OPERATION AT THE MAXI-

MUM CAPACITY

OPERATION AT THE MINI-

MUM CAPACITY

Push the reset

push button for 3

seconds

Push again the reset push

button; the symbol “F” (Cen-

tral Heating) blinks, the sym-

bol “L” (burner in operation) is

fixed.

Push again the reset push

button; the symbol “F” (Cen-

tral Heating) and the symbol

“L” (burner in operation) are

both blinking

fig. 28

Inlet

pressure

test nipple

B = Screw

(red) for

minimum

pressure

adjustment

C = Adjust-

ment nut (10

mm) for

maximum

pressure

3) Ending of basic adjustings

- check the minimum and maximum pres-

sure values of the gas valve;

- if necessary make any fine adjustments

- Clear the chimneysweeper function by cut-

ting off the voltage.

- Remove the plastic pipe from pressure test

nipple and close the inner screw;

- Using a soapy solution check for gas

leaks.

PRESSURE TEST NIPPLE

fig. 29

LA CALDAIA MI DA ERRORE 6C, MA NON SUCCEDE NULLA SE PREMO IL RIPRISTINO O RESET, CHE COSA PUO' ESSERE.?
GRAZIE A TUTTI Submitted on 28-5-2022 at 19:02
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Unical EVE 05 CTFS 24 in the language / languages: English as an attachment in your email.

The manual is 1,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Unical EVE 05 CTFS 24 Manual

Product: