694450
3
Zoom out
Zoom in
Previous page
1/34
Next page
3
Information
Keep this manual so that it is accessible to professionals and future needs.
Read this manual carefully before putting the pellet burner into service.
• Follow the manual and its instructions carefully and do recommended management and maintenance.
Registration to the local building authority in your municipality
N.B.: At every change of heating system, the local building authority of the municipality has to be contacted
and a so called “Construction Registration” is made.
Inspection
Heating plants installed today shall be inspected and approved by authorized inspector like the local certified
chimney-sweeper. The local building authority in the municipality can inform you how this could work.
Important at installation
Run the feed auger of the burner by itself until the pellets start to come in constant flow. This can be made
by connecting the feed cable of the burner directly to the cable of the auger. Run the auger approx. 15min
after the first pellets have reached the outlet on the auger.
The auger shall have a max angle 45 degrees and not be below 43 degrees.
We recommend that the length of the hose, between the burner and the auger, should not be below
500mm. The auger shall also be placed so that it sits a little to the side of the tipping chute of the burner,
this to avoid that pellets can fall down into the burner if back burning would occur when the hose burns off
as a part of the safety.
• Hose inclination must be more than 45 degrees, otherwise the pellets are stuck in the hose.
At adjustment of the burner, the draft limiter should be adjusted after the draft conditions of the chimney.
The feed cable of the burner shall be connected above the overheating protection of the boiler.
Sweeping
Chimney sweeping shall in accordance with the fire-protection law shall be made frequently during the year.
This is made by your local chimney sweeper. Regular cleaning of heating surface of the boiler shall be made
in a way so that good operating economy is obtained. Prepare sweeping by turning off the boiler at least a
couple of hours before cleaning to minimize the amount of glowing ash.
Warning!
See to that the power to the boiler is turned off before the cover over the burner is removed and dismount
cabling to the burner when the burner is removed from the boiler.
Maintenance agreement increases operation length and life of the burner
ULMA AB recommends subscription of annual maintenance agreement.
For more information contact your local ULMA retailer.
Change of wear parts
ULMA AB always recommends that wear parts, when needed, are being changed by an authorized service
technician at your ULMA retailer. Ulma’s retailers can provide necessary spare parts and at change make
sure that the parts being changed on the unit go through alignment and that a flue-gas analysis of the unit is
made.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ulma 40 Kw at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ulma 40 Kw in the language / languages: English as an attachment in your email.

The manual is 1,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ulma 40 Kw

Ulma 40 Kw User Manual - Dutch - 10 pages

Ulma 40 Kw User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info