765111

U.N.O. TR 4.0 Manual

35
Zoom out
Zoom in
Previous page
1/39
Next page
OWNER’S MANUAL
TR 4.0
Please carefully read this entire manual before operating your new treadmill
1
TABLE OF CONTENTS
Important Safety Instructions 2
Important Electrical Instructions 3
Grounding Instructions 3
Important Operation Instructions 4
Assembly Instructions 5
Transport Instructions 11
Features 12
Console Operation 14
Programmable Features 17
Using Heart Rate Transmitter 27
General Maintenance 29
Exploded View Diagram/Parts List 34
ATTENTION
This treadmill is intended for residential use only and is warranted for this application.
Any other application voids this warranty in its entirety.
XT810-AT38CEGS_1109A
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your treadmill from the electrical
outlet prior to cleaning and/or service work.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install
the treadmill on a flat level surface with access to a 230-volt, 10-amp grounded outlet with
only the treadmill plugged into the circuit.
DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH
ONLY ONE OUTLET ON THE END.
The treadmill should be the only appliance in the circuit in which it is connected.
DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING IMPROPER
ADAPTERS, OR IN ANY WAY MODIFY THE CORD SET. A serious shock or fire hazard
may result along with computer malfunctions. See Grounding Instructions, page 3.
Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both carpet
and treadmill may result.
Do not block the rear of the treadmill. Provide a minimum of 3 1/2 feet clearance
between the rear of the treadmill and any fixed object.
Keep children away from the treadmill. There are obvious pinch points and other caution
areas that can cause harm.
Keep hands away from all moving parts.
Never operate the treadmill if it has a damaged cord or plug. If the treadmill is not
working properly, call your dealer.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is being
administered. Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the off position, then remove the plug from the outlet.
Do not attempt to use your treadmill for any purpose other than for the purpose it is
intended.
The hand pulse sensors are not medical devices. Their purpose is to provide you
with an approximate measurement in relation to your target heart rate. Use of a chest
transmitter strap is a much more accurate method of heart rate analysis. Various factors,
including the user’s movement, may affect the accuracy of heart rate readings. The
pulse sensors are intended only as exercise aids in determining heart rate trends in
general.
Use handrails provided; they are for your safety.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for
use on your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
3
IMPORTANT ELECTRICAL INSTRUCTIONS
WARNING!
NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. As with any appliance with a
large motor, the GFCI will trip often. Route the power cord away from any moving part of the treadmill
including the elevation mechanism and transport wheels.
NEVER remove any cover without first disconnecting AC power. If voltage varies by ten percent (10%)
or more, the performance of your treadmill may be affected. Such conditions are not covered under your
warranty. If you suspect the voltage is low, contact your local power company or a licensed electrician for
proper testing.
NEVER expose this treadmill to rain or moisture. This product is NOT designed for use outdoors, near a
pool or spa, or in any other high humidity environment. The operating temperature specification is 40 to
120 degrees Fahrenheit, and humidity is 95% non-condensing (no water drops forming on surfaces).
Circuit Breakers: Some circuit breakers used in homes are not rated for high inrush currents that can
occur when a treadmill is first turned on or even during use. If your treadmill is tripping the house circuit
breaker (even though it is the proper current rating) but the circuit breaker on the treadmill itself does not
trip, you will need to replace the home breaker with a high inrush type. This is not a warranty defect.
This is a condition we as a manufacture have no ability to control. This part is available through most
electrical supply stores. Examples: Grainger part # 1D237, or available online at www.squared.com
part # QO120HM.
GROUNDING INSTRUCTIONS
This product must be grounded. If the treadmill should malfunction or breakdown, grounding provides a path
of least resistance for electric current, reducing the risk of electric shock. This product is equipped with a cord
having an equipment-grounding plug. The plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly
grounded. Do not modify the plug provided with the product if it will not fit the outlet; have a proper outlet
installed by a qualified electrician.
This product is for use on a nominal 230-volt circuit, and has a grounding plug that looks like the plug
illustrated below. A temporary adapter that looks like the adapter illustrated below may be used to
connect this plug to a 2-pole receptacle as shown below if a properly grounded outlet is not available. The
temporary adapter should be used only until a properly grounded outlet, (shown below) can be installed
by a qualified electrician. The green colored rigid ear-lug, or the like, extending from the adapter, must be
connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is
used, it must be held in place by a metal screw.
4
IMPORTANT OPERATION INSTRUCTIONS
NEVER operate this treadmill without reading and completely understanding the
results of any operational change you request from the computer.
Understand that changes in speed and incline do not occur immediately. Set your
desired work level on the computer console and release the adjustment key. The
computer will obey the command gradually.
NEVER use your treadmill during an electrical storm. Surges may occur in your
household power supply that could damage treadmill components. Unplug the
treadmill during an electrical storm as a precaution.
Use caution while participating in other activities while walking on your treadmill;
such as watching television, reading, etc. These distractions may cause you to lose
balance which may result in serious injury.
Do not use excessive pressure on console control keys. They are precision set to
function properly with little finger pressure.
SAFETY TETHER CORD
A safety tether cord is provided with this unit. It is a simple magnetic design that
should be used at all times. It is for your safety should you fall or move too far back on
the tread-belt. Pulling this safety tether cord will stop tread-belt movement.
To Use:
1. Place the magnet into position on the round metal portion of the console control head.
Your treadmill will not start and operate without this. Removing the magnet also
secures the treadmill from unauthorized use.
2. Fasten the plastic clip onto your clothing securely to assure good holding power. Note:
The magnet has strong enough power to minimize accidental, unexpected stopping.
The clip should be attached securely to make certain it does not come off. Be familiar
with its function and limitations. The treadmill will stop, depending on speed, with a
one to two step coast anytime the magnet is pulled off the console. Use the Stop /
Pause switch in normal operation.
5
ASSEMBLY INSTRUCTIONS
!!ATTENTION: IMPORTANT UNPACKING INSTRUCTIONS. PLEASE READ
BEFORE UNPACKING YOUR FOLDING TREADMILL!!
Serious injury could occur if this folding treadmill is not unpacked properly.
There is a Velcro strap installed around the treadmill base that prevents the treadmill
from unfolding accidentally during shipping. If this strap is not removed properly the
treadmill could spring open unexpectedly and cause injury if someone is standing near
the treadmill when the strap is removed.
To ensure your personal safety during removal of the shipping strap please make sure
the treadmill is positioned flat on the ground, in the orientation it would be in if you were
using the treadmill. Do not turn the treadmill up on its side while removing the shipping
strap. This could cause the treadmill’s folding mechanism to spring open. If the end of
the Velcro strap (that you need to grab to remove it) happens to be under the treadmill
deck, reach under the deck to grab it, but do not tilt the treadmill up to gain access to
the strap end.
Cut the banding straps with a short box cutter (razor knife); separate the carton from the
one underneath it by prying up on the staples (if applicable). Pull the carton over the
treadmill parts and locate the hardware pack. The hardware pack is separated into five
sections; one section containing tools and four sections labeled steps 1-4 which contain
the hardware needed for assembly of each step. The assembly steps below are
numbered one through four and correspond to the hardware in the numbered sections
of the hardware pack. Remove only the hardware for the step you are currently
assembling to avoid confusion and mix ups.
Then remove the treadmill from the carton and lay it on a level surface.
ASSEMBLY TOOLS
#
1
07
.
Combination M5 Allen Wrench
& Phillips Head Screw Driver #109. Phillips Head Screw Driver #18. Deck/Belt Lubricant
#106. M6 Allen Wrench #63. Safety Key
6
UPRIGHT TUBE ASSEMBLY
1. Slide the bottom console covers onto the console mast tubes (52 onto 5 Left side & 53 onto 4
Right side). Make sure they are oriented as shown in the illustration.
2. Connect computer cables (32 & 33) on the right side.
3. Insert console mast tubes (4 & 5) into the frame. Caution: Be careful not to pinch the cables you
just connected. Doing so could affect the console function. Pull the end of the cable tight as
you insert the right console mast tube.
4. Insert three Button Head Socket Bolts (102) and one Button Head Socket Bolt (103) and Split
Washer (108) on each side. Partially tighten these using the M6 Allen Wrench (106). Don’t
completely tighten these until the end of step 3.
HARDWARE
1
#
102
. 5/16” x 15mm
Button Head Socket
Bolt (6 pcs)
#
108
. 3/8” x 2T
Split Washer
(2 pcs)
#
103
. 3/8” x 2”
Button Head Socket
Bolt (2 pcs)
7
8
CONSOLE ASSEMBLY
1. Connect the following cables together: Incline cables 35 to 39, Speed cables 34 to 38, and
Computer cables 33 to 31.
2. Place the console (37) onto the brackets at the top of the console mast tubes and attach with two
Button Head Bolts (104) and two Split Washers (108) on each side. Caution: Be careful not to
pinch any of the cables. Doing so may affect the console function. Firmly tighten with the
Combination M5 Allen Wrench & Phillips Head Screw Driver (107).
HARDWARE
2
#
108
. 3/8” x 2.0T
Split Washer (4 pcs)
#
104
. 3/8” x 1
-
3/4”
Button Head Socket
Bolt (4 pcs)
9
BASE COVERS
1. Attach the bottom console covers (52 & 53) to the console with five Sheet Metal Screws (105)
on each side. Tighten with the Phillips Head Screw Driver (109) or Combination M5 Allen
Wrench & Phillips Head Screw Driver (107).
2. Attach the cross brace (3) to the console mast tubes (4 & 5) with two Button Head Socket Bolts
(102) on each side. Tighten with the M6 Allen Wrench (106).
3. Firmly tighten the eight Button Head Socket Bolts inserted in Step 1 with the M6 Allen Wrench
(106). Place the accessory holder tray (48) securely on top of the cross brace (3).
HARDWARE
3
#
102
. 5/16” x 15mm
Button Head Socket
Bolt (4 pcs)
#
105
. 3.5 x 12mm
Sheet Metal Screw
(10 pcs)
34
EXPLODED VIEW DIAGRAM
87
83
1
43
87
83 43
109
117 117
118
118
116
100
9187
87
51
87
84
84
96
17
147
147
87
87 87
87
84
84
84
87 96
17
87
83
92
92
146
146
84
147
41
40
147 46
87
87
46
147
43
43
32
87 23 76 78
24
43
65
83
87
83
87
83
87
98
60
28
29
30
17
96 95
82
144
65
98
98
25
26
27
87
74
87
87
68
19
10 77
69
43
3
9
22
86
87
82
144
20
36
79 79
85 85
45
92
92 147
58
82
144 21
66
72
72
71
72
72
72
71
72
106 107
000922PM0300
62
61
70
70 11
60
12
13
124
123
91
87
82
82
4
5
119
6
102
108
102
102
103
87
37-1
37-4
37-27
144
145
139
37-28
37-29
37-5
53
105
105
142
38
42
108
104
108
104
14
94
94
14
102
102
102
39
42
141
80
140
89 89
63
37-17
37-16
31
34
89
89
37-20
37-19
37-19
37-30
37-30
37-7 37-8 37-10
37-10
89
35
135
37-32
37-22
89
37-26
37-25
37-24
89
89
89
89
37-9
89
37-2
37-3
37-31 37-22
37-32
89
135
119
119 80
90
80
90
50-2
80
90
50-3
80
90
50-5 50-4
93
93
50-4
50-3
50-5
105
105
105
37-6
145
145
145
102
103
102
102
52
108
89
54 33
37-21 37-21
137
138
18
48
37-31
37-31
37-31
37-31 37-31
47
47
148
37-34
37-18
151
150 149
87 87
153
156 156
157
155
154
86
64
86
86
64
86
75
73
73
78
76 78 67
73
78
73 78 75
2
59
59
56
56
44
44
44
44
56
56 59
59
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for U.N.O. TR 4.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of U.N.O. TR 4.0 in the language / languages: English as an attachment in your email.

The manual is 2,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of U.N.O. TR 4.0

U.N.O. TR 4.0 User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info