Manual U.N.O. TR 4.0 (page 32 of 39) (English)

765111

Zoom out

Zoom in

1/39

BELT/DECK LUBRICATION PROCEDURE

Do not lubricate with other than approved lubricant. Your

treadmill comes with one tube of lubricant and extra tubes can

be ordered directly from your authorized dealer. There are

commercially available lube kits, but the only one currently

approved is Lube-N-Walk.

These kits come with an application wand that makes applying

the lubrication easier. The kits can be purchased directly from

Lube-N-Walk here: http://www.jadfitness.com/. The proper kit

should be silicon based, NOT paraffin wax.

Keeping the deck lubricated at the recommended intervals ensures the longest life possible

for your treadmill. If the lubricant dries out, the friction between the belt and deck rises and

places undue stress on the drive motor, drive belt and electronic motor control board, which

could result in catastrophic failure of these expensive components. Failure to lubricate the

deck at regular intervals may void the warranty. The belt & deck come pre-lubricated and

subsequent lubrication should be performed every 180 hours of use. The console has a built

in lubrication reminder indicator that lights every 180 hours of use.

Use the Lubricant to lubricate the deck beneath the belt. If you can reach under the belt

approximately 6” on each side, use the following procedure: Unplug the electrical cord. At the

middle of the deck, lift up on the belt and reach under with the tube of lubricant. Squirt most of

the lubricant on the deck surface. Repeat the process on the opposite side. Plug the electrical

cord back into the outlet and walk on the belt at a moderate speed for five minutes.

If unable to perform the above procedure, it will be necessary to loosen the walking belt. Using

the 6 mm Allen wrench supplied, loosen the two rear roller adjustment bolts -- located in the

rear end caps – enough to get your hand under the belt (5 –10 turns). Make sure to loosen

both bolts the same amount of turns and also remember how many turns, because when

finished you will need to tighten the bolts back to the point they were before.

Once the belt is loose, wipe the deck with a clean lint free cloth to remove any dirt. Apply the

whole tube of lubricant onto the deck surface about 45 cm (18 inches) from the motor cover.

Squeeze out the contents of the tube across the deck (parallel to the motor cover) in about a

one-foot line, like toothpaste on a toothbrush. The one-foot line should be in the middle of the

deck at approximately equal distance from both side edges of the belt. You want the lubricant to

be applied about the spot that your feet would hit the belt as you are walking. This should be

about 18 inches from the motor cover, but you may want to walk on the treadmill before

loosening the belt to note where your feet land on the belt. If you mostly use the treadmill for

running, the spot where your feet land may be different from walking. Once the lubricant is

applied, tighten the rear roller bolts the same amount of turns as when you loosened them. Run

the treadmill at about 5 kmph (3 mph) without walking on it for about a minute or two to make

sure the belt stays in the middle of the deck. If the belt tracks to one side then follow the belt

tracking instructions to remedy. Now the deck is lubricated and you should walk, not run, on the

treadmill immediately for at least 5 minutes to ensure the lubricant is evenly distributed. If you

purchase a silicone based Lube-N-Walk kit, follow the instructions that come with it to apply the

lubrication.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of U.N.O. TR 4.0 in the language / languages: English as an attachment in your email.

The manual is 2,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of U.N.O. TR 4.0

U.N.O. TR 4.0 User Manual - French - 40 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

U.N.O. TR 4.0 Manual

Product: