Manual Turbionaire Smart 10 eco (page 10 of 126) (English, German, French, Italian, Spanish)

804591

Zoom out

Zoom in

1/126

c. Before proceeding, make sure that:

d. Mechanical handling equipment is available if it is necessary for the handling of

coolant cylinders;

e. All individual protection equipment are available and correctly used;

f. the recovery process is permanently supervised by a qualified person;

g. The recovery equipment and cylinders are in accordance with the appropriate

standards.

h. If possible, drain the cooling system.

i. If aspiration is not possible, use a collector so that the refrigerant can be removed from

different parts of the system.

j. Ensure that the cylinder is in upright position before recovery.

k. Start the recovery machine and use it in accordance with the instructions of the

manufacturer.

l. Do not fill the cylinders. (Must not exceed 80% of the quantity of liquid).

m. Do not exceed the maximum working pressure of the cylinder, even temporarily.

n. When the cylinders have been correctly loaded and the process has been completed,

make sure that the cylinders and the equipment are quickly removed from the working area

and that all the insulation valves of the equipment are closed.

o. The recovered refrigerant must not be loaded into another cooling system unless it has

been cleaned and checked.

17. Labelling

The equipment must be labelled with the mention that it has been dismantled and emptied

by the refrigerant. The label must be dated and signed. Ensure that there are labels on the

equipment showing that the equipment contains flammable refrigerant.

18. Recovery

When performing the procedure of removing the refrigerant from a system, either for

service or for decommissioning, it is recommended that all refrigerants are safely removed.

When transferring the refrigerant to cylinders, make sure that only the recovery cylinders

are used for the refrigerant. Ensure that the correct number of cylinders is available to take

up the total quantity of the refrigerant in the system. All cylinders to be used are intended

for the recovered refrigerant and labelled for the respective refrigerant (i.e. special

cylinders for the recovery of the refrigerant). The cylinders must be equipped with the

pressure valve and the associated shut-off valves in good working order. Drained recovery

cylinders are evacuated and, if possible, cooled before recovery.

The recovery equipment must be in good working order, provided with a set of available

equipment instructions and be suitable for the recovery procedure of flammable

refrigerants. In addition, a set of calibrated scales must also be available in good working

order. Hoses must be equipped with connection mechanisms without leakage and in good

condition. Before using the recovery machine, make sure it is in good working condition,

that it was properly maintained and that all associated electrical components are sealed to

prevent ignition when a coolant is released. Consult the manufacturer if in doubt. The

recovered refrigerant will be accordingly returned to the supplier of the refrigerant in the

recovery cylinder and the note referring to the transfer of waste will be prepared. Do not

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Turbionaire Smart 10 eco in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 13.89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Turbionaire Smart 10 eco Manual

Product: